manualshive.com logo in svg

Carrier WeatherExpert 48LC B14 Series, Руководство по установке

Поделиться
Скачать
Carrier WeatherExpert 48LC B14 Series Скачать руководство пользователя страница 39

39

Variable Air Volume (VAV) with Variable Fre-
quency Drive

The Variable Air Volume (VAV) system utilizes a Variable Fre-

quency Drive (VFD) to modulate supply fan speed using a PID

and an analog input from a duct static pressure sensor. The supply

fan will adjust to meet the configured static set point regardless of

cooling stage. In heating mode, the latest VAV Open air terminals

offer a minimum airflow setting. This shall be configured to main-

tain the required airflow (CFM) whenever the RTU is in a heating

mode per the unit’s specification. The Open VAV terminals will

recognize the Heating or Warm-up modes as a heat mode and uti-

lize the higher airflow minimum setpoint as configured. The sys-

tem will further monitor the SAT of the RTU to determine if the

SAT is approaching the configured maximum limit. As the limit is

approached, the Linkage mode is changed to Linkage Pressuriza-

tion to ensure all terminals open to their maximum supply airflow.

See Fig. 54 and 55.

Fig. 54 — Variable Frequency Drive (VFD)

Fig. 55 — VFD Location

MULTI-SPEED VFD DISPLAY KIT (FIELD-INSTALLED
OPTION)
NOTE: The Remote VFD Keypad is part of the Multi-Speed VFD

display kit (PN: CRDISKIT002A00) which is a field-installed op-

tion. It is not included with the 48LC*B14-26 base units.

230V/460V

575V ONLY

Содержание WeatherExpert 48LC B14 Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды