Carrier WeatherExpert 48LC B14 Series Скачать руководство пользователя

Страница: 43 / 56

f. Press

and then use the

▲

and

▼

(Up and Down

Arrow) keys to scroll to the proper motor horsepower.
Press

again to set the selected hp.

g. Press

▼

(Down Arrow) once, the following display

appears:

h. Press

to highlight the voltage value. Use the

▲

and

▼

(Up and Down Arrow) keys to select the

nameplate voltage. Press

again to set the selected

voltage.

i. Press

▼

(Down Arrow) once to display the following:

j. Press

to highlight the Frequency value and then

use the

▲

and

▼

(Up and Down Arrow) keys to

select the nameplate Hz. Press

again to set the

selected Hz.

k. Press

▼

(Down Arrow) once to display the following:

l. Press

to highlight the Current value and then use

the

▲

and

▼

(Up and Down Arrow) keys to select

the Max Amps value provided. Press

again to set

the selected Max Amps.

NOTE: The Max Amps is greater than the nameplate value.

Check the VFD Unit Parameters (see Tables 10-14 on pages

46-51) and use the value listed for the given unit in the column

labeled “Motor Current Must-Hold Amps”.

m. Press

▼

(Down Arrow) once to display the following

n. Press

to highlight the rpm value and then use the

▲

and

▼

(Up and Down Arrow) keys to select the

nameplate rpm. Press

again to set the selected

rpm.

6. Entering Parameters for 1-71, 1-73, 1-82, and 1-90:

a. Press the

Menu

key to move the

▼

(triangle icon) so

it is positioned over Main Menu. The display shows
the following:

b. Press

▼

(Down Arrow) once to highlight the bottom

row.

c. Press

, the display changes to:

d. Press

▼

(Down Arrow) until the following display

appears:

e. Press

, the following display appears:

f. Press

to highlight the number and then use the

▲

and

▼

(Up and Down Arrow) keys to select the num-

ber provided in Tables 10 -14. Press

again to set

the selected value.

g. Press

▼

(Down Arrow) twice, the following display

appears:

h. Press

to highlight the number in the bracket and

then use the

▲

and

▼

(Up and Down Arrow) keys to

select the number provided in Tables 10 -14. Press

again to set the selected value.

i. Press the

Back

key once, the following display

appears:

j. Press

▼

(Down Arrow) once, the following display

appears:

k. Press

, the following display appears:

l. Press

▼

(Down Arrow) once, the following display

appears:

m. Press

to highlight the number and then use the

▲

and

▼

(Up and Down Arrow) keys to select the num-

ber provided in Tables 10 -14. Press

again to set

the selected value.

n. Press the

Back

key once, the following display

appears:

o. Press

▼

(Down Arrow) once, the following display

appears:

p. Press

, the following display appears:

q. Press

to highlight the number in the bracket then

use the

▲

and

▼

(Up and Down Arrow) keys to

select the number provided in Tables 10 -14. Press

again to set the selected value.

7. Setting References:

a. Press the

Menu

key to move the

▼

(triangle icon) so

it is positioned over Main Menu. The display shows

the following:

b. Press

▼

(Down Arrow) three times, the following

display appears:

1-22 Motor Voltage

230V

1-23 Motor Frequency

60Hz

1-24 Motor Current

6.61A

1-25 Motor Nominal Speed

1740 rpm

0—** Operation / Display
1—** Load and Motor

1—0* General Settings
1—1* Motor Selection

1—6* Load Depen. Setting
1—7* Start Adjustments

1-71 Start Delay

2.0s

1-73 Flying Start

[1] Enabled

1—6* Load Depen. Setting
1—7* Start Adjustments

1—7* Start Adjustments
1—8* Stop Adjustments

1-80 Function at Stop

[0] Coast

1-82 Min Speed for Functio…

1.0 Hz

1—7* Start Adjustments
1—8* Stop Adjustments

1—8* Stop Adjustments
1—9* Motor Temperature

1-90 Motor Thermal Prote…

[4] ETR trip 1

0—** Operation / Display
1—** Load and Motor

2—** Brakes
3—** Reference / Ramps

Содержание WeatherExpert 48LC B14 Series

























































Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Похожие инструкции для WeatherExpert 48LC B14 Series

Бренды по названию

Популярные бренды

Carrier WeatherExpert 48LC B14 Series, Руководство по установке

Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Похожие инструкции для WeatherExpert 48LC B14 Series

Бренды по названию

Популярные бренды