Carrier TP-WEM01 страница 1 Скачать руководство пользователя

Страница: 1 / 109

Edition Date: 07/20/15

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Replaces: 04/19/15

Advanced Installation and Configuration Instructions

Contents

How to Use This Document ............................................................................................. 3

Wiring Diagrams .............................................................................................................. 4

Installations without a Common (C) Wire ........................................................................ 9

Equipment Configuration ............................................................................................... 13

Accessing the Service Menus .................................................................................... 13

Edit Service Information ............................................................................................. 13

Installation Settings .................................................................................................... 14

Equipment Setup .................................................................................................... 14

Air Conditioner (AC) Configuration Options ......................................................... 14

Furnace Configuration Options ............................................................................ 16

Heat Pump Configuration Options ....................................................................... 18

FanCoil Configuration Options ............................................................................ 25

Humidifier Configuration Options ......................................................................... 27

Dehumidifier Configuration Options ..................................................................... 32

Ventilator Configuration Options .......................................................................... 37

View Wiring ............................................................................................................. 48

Reconfigure Equipment .......................................................................................... 49

Thresholds ................................................................................................................. 51

Auto Change Over and Deadband .......................................................................... 51

Compressor Configurations .................................................................................... 52

Auxiliary Heat Configuration (Heat Pumps) ............................................................ 61

Heat Configuration (Furnace) ................................................................................. 69

Temperature Offset ................................................................................................. 75

Humidity Offset ....................................................................................................... 76

Zoning Enabled....................................................................................................... 77

Variable Speed Blower ........................................................................................... 78

Test Equipment .......................................................................................................... 80

Dehumidification Options ........................................................................................... 81

Содержание TP-WEM01














































































































Результаты поиска

Содержание TP-WEM01

Отзывы:

Похожие инструкции для TP-WEM01

Бренды по названию

Популярные бренды

Carrier TP-WEM01, Расширенные инструкции по установке и настройке

Результаты поиска

Содержание TP-WEM01

Отзывы:

Похожие инструкции для TP-WEM01

Бренды по названию

Популярные бренды