Carrier 09FC020 Скачать руководство пользователя | Manualshive

Страница: 1 / 72

background image

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53090030 -01

Printed in U.S.A.

Form 09FC-1SI

Pg 1

3-21

Replaces: NEW

Installation, Start-Up and

Maintenance Instructions

CONTENTS

Page

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . 1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

• PROVIDE MACHINE PROTECTION

• INSPECTION DURING STORAGE

Inspect Shipment . . . . . . . . . . . . . . . . . . . . 6

Rig and Place Unit . . . . . . . . . . . . . . . . . . . 6

• PLACING UNITS

• MOUNTING UNITS

Connect Chilled Water Loop . . . . . . . . . . 17

• AIR SEPARATION

• FIELD PIPING

• MODULAR UNIT SERIES PIPING (09FC050 - 080)

Fill the Chilled Water Loop . . . . . . . . . . . 21

• WATER SYSTEM CLEANING

• WATER TREATMENT

• FILLING THE SYSTEM

• SET WATER FLOW RATE

Make Electrical Connections . . . . . . . . . . 24

• POWER SUPPLY

• POWER WIRING

• ENABLE SIGNAL

• COMMUNICATION OPTIONS

Install Accessories/Optional Equipment 29

• LOW AMBIENT OPERATION

• FIELD-INSTALLED ACCESSORY INSTALLATION

CONTROLS   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Control Boards   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Carrier AppController  . . . . . . . . . . . . . . . . . . . . . . . . 30
Required Configurations   . . . . . . . . . . . . . . . . . . . . . 31
Carrier Equipment Touch Display  . . . . . . . . . . . . . . 31
Outdoor Fan Control . . . . . . . . . . . . . . . . . . . . . . . . . 42

• VFD DISPLAY NAVIGATION

• VFD ALARMS AND ALERTS

Field Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 50

• LEAVING WATER SETPOINT

• OUTDOOR AIR SETPOINT

Communication - BACnet . . . . . . . . . . . . . . . . . . . . . 51
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

• SEQUENCE OF OPERATION

• LOW AMBIENT START

• SNOW CLEARING

START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

• NON-OPERATIONAL COMPONENT ALARM

• REVERSE LOAD WATER FLOW ALARM

• THERMISTOR ALARM

• FAN VFD FAILURE

Alarm Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .54

• LEAVING WATER TEMPERATURE ALARM

• LEAVING WATER SENSOR FAILURE ALARM

• ENTERING WATER TEMPERATURE ALARM

• ENTERING WATER SENSOR FAILURE ALARM

• OUTDOOR AIR TEMPERATURE ALARM

• OUTDOOR AIR SENSOR FAILURE ALARM

• FAN VFD FAILURE

• REVERSE LOAD WATER FLOW ALARM

Controller Troubleshooting . . . . . . . . . . . . . . . . . . .55
To Restore Defaults . . . . . . . . . . . . . . . . . . . . . . . . . .56

• TO REPLACE THE CONTROLLER’S BATTERY

Fluid Piping System . . . . . . . . . . . . . . . . . . . . . . . . . .56
Check Valve  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
3-Way Bypass Valve   . . . . . . . . . . . . . . . . . . . . . . . . .56
Valve Linkage Adjustment   . . . . . . . . . . . . . . . . . . . .56
Thermistor   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
External Control Valve . . . . . . . . . . . . . . . . . . . . . . . .57
Replacing Thermistors (EWT, LWT) . . . . . . . . . . . . .57
Replacing Thermistor (OAT)  . . . . . . . . . . . . . . . . . . .57
Thermistor/Temperature Sensor Check   . . . . . . . . .57
Fan Blade and Fan Motor Service   . . . . . . . . . . . . . .59
Round Tube Plate Fin Condenser Coil Cleaning   . .60
Remove Surface Loaded Fibers  . . . . . . . . . . . . . . . .60
Periodic Clean Water Rinse   . . . . . . . . . . . . . . . . . . .60
Routine Cleaning of Coil Surfaces  . . . . . . . . . . . . . .60
Totaline Indoor/Outdoor Coil Cleaner Instructions  60

• REQUIRED EQUIPMENT

Application Instructions  . . . . . . . . . . . . . . . . . . . . . .60
Variable Frequency Drives  . . . . . . . . . . . . . . . . . . . .61
MAINTENANCE   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Recommended Maintenance Schedule  . . . . . . . . . .61
Coil Maintenance and Cleaning  . . . . . . . . . . . . . . . .61
APPENDIX A

CONTROL PANEL COMPONENT

LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
APPENDIX B

09FC FREE COOLING MODULE

CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

SAFETY CONSIDERATIONS

Installing, starting up, and servicing this equipment can be hazard

-

ous due to system pressures, electrical components, and equip

-

ment location (roofs, elevated structures, etc.).

09FC020-080

Free Cooling Unit

50/60 Hz

1
2
3
...
»

Содержание 09FC020









































































Отзывы:

Нет отзывов

Похожие инструкции для 09FC020

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды