Carrier 09FC020 Скачать руководство пользователя

Страница: 49 / 72

LEGEND

NOTE:

1. Warning or Alarm is determined by the setting of the reference

Parameter.

062

Warning

Output

Frequency at

Maximum Limit

The output frequency has reached the

value set in parameter 4-19 Max Output

Frequency

The warning clears when the output drops below

the maximum limit

064

Warning

Voltage Limit

Supply Voltage is too low

Check supply voltage to determine if within

permissable limits of VFD

065

Warning/

Alarm

Control Card

Over-

Temperature

The temperature limit of the control card

has been exceeded

• Check that the ambient operating temperature

is within the limits.

• Check for clogged filters.

• Check the fan operation.

• Check the control card

066

Warning

Heat Sink

Temperature Low

The frequency converter is too cold to

operate. This warning is based on the

temperature sensor in the IGBT module

Confirm that the VFD heater is working properly

by checking voltage across the heater terminals,

120V should be present at low temperatures

which would trigger this warning

068

Alarm

Safe Stop

Safe Stop input has been activated

Yes

Check Compressor High Pressure Switch

5-19 Terminal

37 Safe Stop

069

Alarm

Power Card

Temperature

The temperature sensor on the power card

is either too hot or too cold

• Check that the ambient operating temperature

is within limits.

• Check for clogged filters.

• Check fan operation.

• Check the power card

072

Alarm

Emergency Stop An unexpected combination of failures

Contact Carrier Service

098

Warning

Clock Fault

Time is not set or the RTC clock has failed

Reset the clock in parameter 0-70 Date and Time.

Contact Carrier Service

0-7* Clock

Settings

243

Warning/

Alarm

IGBT Fault

IGBT is defective or not functioning

properly

Contact Carrier Service

244

Warning/

Alarm

Heat Sink

Temperature

This alarm is generated by the Variable Fre-

quency Drive. The alarm will be generated if

the maximum temperature of the heat sink

has been exceeded. The temperature fault

cannot reset until the temperature drops

below a defined heat sink temperature. The

trip and reset points are different based on

the power size. This alarm is equivalent to

A29 - Heat Sink Temp.

The circuit is

shut down or not

allowed to start.

Automatic, after heat sink temperature falls below

a preset point.

246

Alarm

Power Card

Supply

247

Alarm

Power Card

Temperature

Table 13 —

Alarms List (cont)

CODE WARNING/

ALARM

DESCRIPTION

POSSIBLE CAUSES

DOES MACHINE

SHUT DOWN

ACTION TO

BE TAKEN

REFERENCE

PARAMETER

AMA

—

Automatic Motor Adaptation

IGBT

—

Insulated Gate Bipolar Transistor

PTC

—

Positive Temperature Coefficient

VFD

—

Variable Frequency Drive

Содержание 09FC020









































































Результаты поиска

Содержание 09FC020

Отзывы:

Похожие инструкции для 09FC020

Бренды по названию

Популярные бренды

Carrier 09FC020, Инструкции по установке, запуску и обслуживанию

Результаты поиска

Содержание 09FC020

Отзывы:

Похожие инструкции для 09FC020

Бренды по названию

Популярные бренды