Carrier 09FC020 Скачать руководство пользователя страница 65

Страница: 65 / 72

APPENDIX B

—

09FC FREE COOLING MODULE CONTROLLER (CONT)

Service Configuration

Navigation: i-Vu

/ Field Assistant: Properties > Control Program

> Configuration > Service Configuration

Point Name – Description

Default/Range

Remote Contact Normal Logic State

– Specifies the remote contact's normal logic state.

D: Open

R: Open/Closed

Fan VFD Run Status Normal Logic State

– Specifies the fan's variable frequency drive run status normal

logic state.

D: Open

R: Open/Closed

Fan VFD Output Type

– Defines the type of fan variable frequency drive output control.

D: 0-10V

R: 0-10V/2-10V

Fan Initial Start Speed

– The speed that the module’s fans are briefly run on initial startup.

D: 100%

R: 0 to 100%

Fan Minimum Speed

– The lowest speed that the module’s fan is commanded when the fans’ variable

frequency drive is enabled.

D: 20%

R: 0 to 100%

Fan Speed PID

– This BACnet Object calculates the amount of fan speed required to satisfy the

Leaving

Water Temp Setpoint

and allows access to the control loop's tuning parameters.

NOTE

: The following default values should be changed only by a technician trained in tuning PI

D Loop algorithms.

R: 0 to 100%

Action

Update Interval

Proportional

Integral

Derivative

Deadband

Bias

direct

1:00 mm:ss

Bypass Valve Type

– Defines the type of bypass valve analog output control.

D: 0-10V

R: 0-10V/2-10V

Bypass Valve PID

– This BACnet Object calculates the amount of bypass required to satisfy the

Leaving

Water Temp Setpoint

when bypass valve modulation is enabled and allows access to the control loop's

tuning parameters.

NOTE The following default values should be changed only by a technician trained in tuning PI

D Loop algorithms.

R: 0 to 100%

Action

Update Interval

Proportional

Integral

Derivative

Deadband

Bias

reverse

1:00 mm:ss

System Cool Demand Level

– The system cool demand level being received over the network.

D: 0.00

R: 0 to 3

System Leaving Water Temperature

– Allows using another controller's leaving water temperature sensor

value (system water temperature), to be read over the network. The remote controller must have a network-

accessible leaving water temperature sensor value.

D: -999°F

R: -25 to 125°F

System Entering Water Temperature

– Allows using another controller's entering water temperature

sensor value (system water temperature), to be read over the network. The remote controller must have a

network-accessible entering water temperature sensor value.

D: -999°F

R: -25 to 125°F

System Outdoor Air Temperature

– Allows using another controller's outdoor air temperature value over

the network. The remote controller must have a network accessible outdoor air temperature sensor value.

D: -999°F

R: -50 to 150°F

System Control Setpoint

– Allows using another controller's Control Setpoint value to be read over the

network. The remote controller must have a network-accessible point.

D: -999°F

R: -20 to 65°F

System Occupancy

– Allows reading and using another controller's occupancy status value over the

network. The remote controller must have a network-accessible Occupancy Status point.

D: Unoccupied

R: Unoccupied/Occupied

Equipment Alarm Lamp Initiators

Lvg Water Temp Alarm

– When set to

Enable

, any Leaving Water Temperature Alarm indicated by the

controller also initiates an

Equipment Alarm

and energizes the

Alarm Lamp

binary output.

D: Enable

R: Disable/Enable

Lvg Wtr Sensor Fail Alarm

– When set to Enable, any Leaving Water Temperature Sensor Failure Alarm

indicated by the controller also initiates an Equipment Alarm and energizes the Alarm Lamp binary output.

D: Enable

R: Disable/Enable

Ent Water Temp Alarm

– When set to

Enable

, any Entering Water Temperature Alarm indicated by the

controller also initiates an

Equipment Alarm

and energizes the

Alarm Lamp

binary output.

D: Enable

R: Disable/Enable

Ent Wtr Sensor Fail Alarm

– When set to

Enable

, any Entering Water Temperature Sensor Failure Alarm

indicated by the controller also initiates an

Equipment Alarm

and energizes the

Alarm Lamp

binary output.

D: Enable

R: Disable/Enable

Outdoor Air Temp Alarm

– When set to

Enable

, any Outdoor Air Temperature Alarm indicated by the

controller also initiates an

Equipment Alarm

and energizes the

Alarm Lamp

binary output.

D: Enable

R: Disable/Enable

Outdoor Air Sensor Fail Alarm

– When set to

Enable

, an Outdoor Air Temperature Sensor Failure Alarm

indicated by the controller also initiates an

Equipment Alarm

and energizes the

Alarm Lamp

binary output.

D: Enable

R: Disable/Enable

Fan VFD Fail Alarm

– When set to

Enable

, a Fan VFD Failure Alarm indicated by the controller also initiates

Equipment Alarm

and energizes the

Alarm Lamp

binary output.

D: Enable

R: Disable/Enable

Lvg Water Temp Hi Alarm

– When set to

Enable

, a High Leaving Water Temperature Alarm indicated by

the controller also initiates an

Equipment Alarm

and energizes the

Alarm Lamp

binary output.

D: Enable

R: Disable/Enable

Negative DeltaT Alarm

– When set to

Enable

, a Negative Differential Temperature Alarm indicated by the

controller also initiates an

Equipment Alarm

and energizes the

Alarm Lamp

binary output.

D: Enable

R: Disable/Enable

Service Test

– When set to

Enable

, any output can be overridden for up to 5 minutes. The

Service Test

has

a 1 hour timeout.

D: Disable

R: Disable/Enable

Содержание 09FC020









































































Результаты поиска

Содержание 09FC020

Отзывы:

Бренды по названию

Популярные бренды

Carrier 09FC020, Инструкции по установке, запуску и обслуживанию

Результаты поиска

Содержание 09FC020

Отзывы:

Бренды по названию

Популярные бренды