CarpeStar SMG Series Скачать руководство пользователя страница 63

Страница: 63 / 139

Page 57

Figure 3-56 Wireless Parameters Modification Interface

The table below explains the configuration items on the Wireless Parameters Modification
interface.

Item

Description

Port

The number of the port corresponding to the wireless module.

Cell Phone No.

The number of the SIM card corresponding to the wireless module. This number

should be configured manually.

Query Mode

It is supported to acquire the SIM card number by two modes SMS and USSD.

Destination Number

Sets the destination number to receive the short message.

Content to Send

Sets the content of the short message.

Keywords to Match

Sets the keywords used to get the cell phone No. from the received SMS.

Bits of Prefix to be

Removed from Phone

No.

Sets the bits of the prefix to be removed from the cell phone No.. Up to 4 bits can be

removed.

Get Phone No. after SIM

Card Registration

Sets whether to get the cell phone No. after the SIM card being registered

successfully.

IP->GSM(WCDMA/CDMA)

Voice Volume

The volume of the voice from IP to GSM/WCDMA/CDMA. By default, the value for

GSM is 3; the value for WCDMA is 10000; the value for CDMA is 1; the value for

SIMCOM is 10400.

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Содержание SMG Series












































































































































Результаты поиска

Содержание SMG Series

Отзывы:

Похожие инструкции для SMG Series

Бренды по названию

Популярные бренды

CarpeStar SMG Series, Руководство пользователя

Результаты поиска

Содержание SMG Series

Отзывы:

Похожие инструкции для SMG Series

Бренды по названию

Популярные бренды