CarpeStar SMG Series Скачать руководство пользователя страница 43

Страница: 43 / 139

Page 37

Access Setting

Sets the IP addresses which can access the gateway via WEB. By default, all IPs

are allowed. You can set an IP whitelist to allow all IPs within it to access the

gateway freely. Also you can set an IP blacklist to forbid all IPs within it to access the

gateway.

SYSLOG Enabled

Sets whether to enable SYSLOG. It is required to fill in

SYSLOG Server Address

and

SYSLOG Level

in case SYSLOG is enabled. By default,

SYSLOG

is disabled.

Server Address

Sets the SYSLOG server address for log reception.

SYSLOG Level

Sets the SYSLOG level. There are three options:

ERROR

WARNING, INFO

and

DEBUG

. The default value is

INFO

AT Debug Enabled

Sets whether to enable the AT debug feature, with the default value of

. Once this

feature is enabled, the related information about AT will be output to the SYSLOG.

Echo Mode Enabled

Sets whether to enable the echo mode, with the default value of

. Once this

feature is enabled, both the sent and received information will be displayed.

Port

Select the port to execute the AT debug. It is allowed to choose a port or all ports.

CDR Enabled

Sets whether to enable the feature of CDR. It is required to fill in

Server Address

and

Server Port

in case CDR is enabled. By default,

CDR

is disabled.

Server Address

Sets the server address to receive CDR.

Server Port

Sets the server port to receive CDR.

Save CDR

Sets whether to save CDR, with the default value of

Amount of Saved

CDR

Sets the amount of saved CDR. Range of value: 200~10000, with the default value

of 5000.

API Enabled

When this feature is enabled, the remote terminal can invoke the API interface. The

default value is

Remote IP Address

allowed to Invoke

API

Sets the remote IP addresses which are allowed to invoke the API interface. Up to 5

addresses can be configured and each of them are separated by

“,”. “*” denotes all

IP addresses are allowed.

Username for API

Call, Password for

API Call

The authorized username and password for calling the API interface.

Time Calibration

Sets the calibration mode for the time. Three options available: NTP, Synchronized

with Operator and Close, with the default value of

Synchronized with Operator

NTP Server Address

Sets the Server address for NTP time synchronization.

Synchronizing Cycle

Sets the cycle for NTP time synchronization. The default value is 3600.

System Time

The system time. Check the checkbox before

Modify

and change the time in the edit

box if

Time Calibration

is set to Close.

Time Zone

The time zone of the gateway.

Daily Restart

Sets whether to restart the gateway regularly every day at the preset

Restart Time

By default, this feature is disabled.

Restart Time

Sets the time to restart the gateway regularly.

Clear Call Count 2

after Restart

When this feature is enabled, the gateway will clear the data of Call Count 2 upon its

restart. By default this feature is disabled.

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Содержание SMG Series












































































































































Результаты поиска

Содержание SMG Series

Отзывы:

Похожие инструкции для SMG Series

Бренды по названию

Популярные бренды

CarpeStar SMG Series, Руководство пользователя

Результаты поиска

Содержание SMG Series

Отзывы:

Похожие инструкции для SMG Series

Бренды по названию

Популярные бренды