14
Fitting the toothed rack
• To fit the toothed rack to the sliding gate proceed as follows:
- release the geared motor (fig.9), lay the first stretch of the
toothed rack on the pinion and fix it to the gate, then fasten
down all the other parts along the entire length of the gate.
- after having fastened the toothed rack, realign the pinion (play
of
1 to 2 mm
between the toothed runner and the pinion) using
the positioning nuts at the base of the geared motor.
This action will prevent the weight of the sliding
gate from damaging the unit when
working.
- Once the unit has been correctly aligned
fasten it down using the lock nuts then
position and fasten down the mechanical
travel limits (opening and closing
directions) mounted on the toothed rack.
• To operate correctly the gate must stop
(closing direction travel limit activated) about
1 cm
before it
makes contact with the mechanical closing direction buffer on
the upper part of the gate (pos. "
E
" fig.1). As there is a slight
deceleration when the travel limit is activated ("
soft stop
", the
gate moves slightly onward due to inertia), position the mechan-
ical travel limit according to the entire travel distance.
- The geared motor unit has been assembled in the factory to be
fitted to the
LEFT SIDE
of the gate (internal view).
To install the motor to the
RIGHT SIDE
of the gate invert the
motor power cables (Red and Black position "
CN3
" on the elec-
tronic card and the travel limit cables (Red and Blue binding
posts "
12
" and "
13
" on the terminal block while the travel limit
common wire (Black position "
11
") remains in the same posi-
tion.
- Using the "
MANUAL MODE
" check the correct functioning of
the gate.
SCALA: 1:2
Prodotti Technocity
SL4024
07-07-98
DI0073
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Nasello finecorsa
SCALA: 1:2
Pr
odotti T
echnocity
SL4024
08-06-98
DI0069
Description :
Pr
oduct Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San V
endemiano (TV) Italy - via Raf
faello, 36 T
el: 0438/401818 Fax: 0438/401831
Draft :
All rights r
eserved. Unauthorised copying or use of the information contained in this document is punishable by law
VIST
A INTERNA CANCELLO SL4024
MANUAL RELEASE MECHANISM
Manual release is carried out with the power to the motor inter-
rupted due to a power failure.
To release the gate use the manual release key supplied with the
unit. The key should be kept inside the house in an easily acces-
sible place or stored with the unit itself.
To release the unit
Remove the cover "
A
" using a screwdriver and insert the key "
B
"
over the T-shaped pin, then rotate the key through 90 degrees in the
direction indicated by the arrow "
C
" (clockwise). This will release
the clutch and separate the gears from the motor allowing you to
manually manoeuvre the gate by pushing lightly on it.
To relock the unit
Follow the above instructions in reverse order rotating the key
through 90 degrees in the direction indicated by the arrow "
D
"
(anticlockwise). Close the release mechanism access cover "
A
".
Never use
the manual release mechanism while the gate is in
operation.
Access to the electronic card
To open the cover insert a screwdriver into the slot "
G
" and turn it
through
90°
as shown in fig.9
Caution!
Before opening the cover make sure that
the power has been switched off at the mains.
SCALA: 1:2
Prodotti Technocity
SL????
12-02-2007
DI0479
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Sblocco motore
B
C
D
A
F
90
°
G
SCALA: 1:2
Prodotti (plinto 350 mm)
SL424EBSB
16-06-2006
DI0409
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
VISTA DI FIANCO CON MOTORE
2 mm
15 mm
25
325
INSTRUCTIONS FOR POSITIONING THE UNIT
9
6
7
Collegamenti scheda base per S449
PRG850
03-06-2002
DI0248
PRG850 (con secondo canale Rx)
P2
1 2
P1
SEL
Fuse T1.6A
Fuse F1A
CS1152A
DC0361
Fuse F10A
PROG
P4
P3
DEL
MEMO
L2
L3
L1
L5
L6
L7
L8
L4
D1
{
CN3
CN2
{
CN1
F1
F3
F2
V1 V2
V0
R1
V3
V4
1
2
3
4
5
6
9
10
11
12
15
16
17
18
13
14
19
20
7
8
26
25
24
23
22
21
28
27
trf 230V~
line 230V~
LC
230V~
N
L
30
29
M1
B1
CHD
CHC
CHB
CHA
J2
CHD
CHC
CHB
CHA
24C16
M1
CHD
CHC
CHB
CHA
J2
B1
1
2
LP
1
2
LS
SEL
1
3
2
CLOSING
COMMON
OPENING
FCA
FCC
TD
TB
LS 24V~
FCC
FCA
FTC_
I
FTC_
S
TC
TA
TA
L
LP 24V~
OUT 24V~
CMN
OUT CH2
1
2
TB
24V 12V 0
C
1
6
5
4
3
2
NA
NC
NC
C
NA
FTC-RX
1
3
2
24V
12V
0
FTC-TX
1
2
PS
NC
NA
J1
J1
Description:
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
9
10
11
12
15
16
17
18
13
14
19
20
TD
TB
LS 24V~
FCC
FCA
FTC_
I
FTC_
S
TC
TA
TA
L
CMN
1
2
3
4
5
6
7
8
LP 24V~
OUT 24V~
OUT CH2
CMN
CMN
CMN
CMN
ANS400
8
Содержание ZVL499.00
Страница 44: ...44 NOTES...
Страница 45: ...45 NOTES...
