Capelec EOBD Скачать руководство пользователя страница 67

Страница: 67 / 69

23/04/2019

Rev 3

V.9.

OPTION:

This sub-menu is dedicated to persons in charge of installing new functions. It is secured by a 5-
digit code.

Select the configuration menu in order to install a new feature.

This windows shows all the functions and options already installed.

V.10.Parameters by default :

WARNING: This window has to be used with caution because it allows resetting all the
configuration values.

V.11.PC keyboard

Declare here whether the virtual or physical keyboard will be used.

Programming « absent keyboard » means the operator will preferably use the virtual keyboard.

V.12.Info Maintenance

This menu access is secured by a maintenance code.

It is possible here to fill in the information about the maintenance company, to add a logo but
also to set the commissioning date.

At the moment of 1st programming, the commissioning date key is active (green). Then, once this
information filled in, it will become inactive in order to make it impossible to be changed.

Содержание EOBD






































































Результаты поиска

Содержание EOBD

Отзывы:

Бренды по названию

Популярные бренды

Capelec EOBD, Руководство пользователя

Результаты поиска

Содержание EOBD

Отзывы:

Бренды по названию

Популярные бренды