Capelec EOBD Скачать руководство пользователя страница 37

Страница: 37 / 69

23/04/2019

Rev 3

II.6.

Messages :

Message displayed

Call

Maintenance

Do it yourself

Leak present

YES

Data invalid

YES

HC out of bounds

YES

CO out of bounds

YES

CO2 out of bounds

YES

O2 out of bounds

YES

NOx out of bounds

Lowflow detected

YES

HC residue in gas inlet

YES

Error com.

YES

Adjustment necessary

YES

Change O2 sensor

YES

Condensation: wait

YES

Heating problem

YES

II.6.1.Leak present

Repeat the test, disconnecting the probe from the device and plugging the gas entry port on the
separator. If the problem disappears, the leak is in the probe tubing.

Otherwise, it affects the machine. Check the filter connections. Check that the separator is
correctly installed and adequately tightened.

Test the various parts of the pneumatic circuit with leak tests, moving the plug progressively
upstream, up to the pumps.

Open the machine and perform a visual check of the pneumatic circuit.

Replace the leaking portion of the pneumatic circuit.

II.6.2.Data invalid

Adjustment necessary.

II.6.3.HC out of bounds

Out of range.

Содержание EOBD






































































Результаты поиска

Содержание EOBD

Отзывы:

Бренды по названию

Популярные бренды

Capelec EOBD, Руководство пользователя

Результаты поиска

Содержание EOBD

Отзывы:

Бренды по названию

Популярные бренды