manualshive.com logo in svg

Canon PIXMA Pro9000 Mark II Series, Руководство по обслуживанию

Поделиться
Скачать
Canon PIXMA Pro9000 Mark II Series Скачать руководство пользователя страница 59

5.  PRINTER TRANSPORTATION 

This section describes the procedures for transporting the printer for returning after repair, etc. 

1)  In the service mode, press the Power button to finish the mode, and confirm that the paper lifting plate of 

the rear tray is raised. 

2)  Keep the print head and ink tanks installed in the carriage. 

See Caution 1 below. 

3)  Turn off the printer to securely lock the carriage in the home position. (When the printer is turned off, the 

carriage is automatically locked in place.) 

See Caution 2 below. 

 

 

- If the print head must be removed from the printer and transported alone, attach the protective 

cap (used when the packing was opened) to the print head (to protect the print head face from 
damage due to shocks). 

- If the packing material that fixed the carriage from the factory is still available, re-use it to fix 

the carriage (to prevent the carriage unlocked during transportation). 

 
 

Pro9000 Mark II

TABLE OF CONTENTS

(1) If the print head is removed from the printer and left alone by itself, ink is likely to 

dry. For this reason, keep the print head installed in the printer even during 
transportation. 

(2) Securely lock the carriage in the home position, to prevent the carriage from 

moving and applying stress to the carriage flexible cable, or causing ink leakage, 
during transportation. Make sure that the carriage is locked in place at power-off. 

<5. PRINTER TRANSPORTATION>  

56 / 56

Содержание PIXMA Pro9000 Mark II Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды