Canon PIXMA Pro9000 Mark II Series Скачать руководство пользователя страница 4

Страница: 4 / 59

1. MAINTENANCE

1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and

Replacement Consumables by Service Engineer

(1) Adjustment

Pro9000 Mark II

TABLE OF CONTENTS

Adjustment

Timing

Purpose

Tool

Approx.

time

EEPROM
initialization

- At logic board replacement

To initialize settings

Service Tool

Perform in the
service mode.

1 min.

Destination
settings
(EEPROM
settings)

- At logic board replacement

To set destination.

Service Tool

Perform in the
service mode.

1 min.

Ink absorber
counter resetting
(EEPROM
settings)

- At logic board replacement
- At ink absorber replacement

To reset the ink absorber
counter.

Service Tool

Perform in the
service mode.

1 min.

Ink absorber
counter value
setting
(EEPROM
settings)

- At logic board replacement

To set the ink amount
data in the ink absorber to
the ink absorber counter.

Service Tool

Perform in the
service mode.

1 min.

Ink absorber
replacement

- When the ink absorber becomes

full

To replace the ink
absorber with a new one.

Screwdriver, a
pair of
tweezers, etc.

10 min.

Paper feed motor
position
adjustment

- At paper feed motor replacement To adjust the belt tension.

(Position the paper feed
motor so that the belt is
stretched tight.)

None.

5 min.

Automatic print
head alignment

- At print head replacement
- At logic board replacement
- When print quality is not

satisfying

To secure the dot
placement accuracy.

None.
Perform in the
user mode.

5 min.

Grease
application

- At carriage unit replacement
- At PR lift shaft replacement
- At other part replacement

To maintain sliding
properties of the carriage
shaft, PR lift shaft, other
sliding parts, and gears.

- EU-1
- FLOIL GP-

1000R

- MOLYKOTE

PG641

- FLOIL KG-

107A

- MOLYKOTE

1 min.

1 / 56

Содержание PIXMA Pro9000 Mark II Series




























































Результаты поиска

Содержание PIXMA Pro9000 Mark II Series

Отзывы:

Бренды по названию

Популярные бренды

Canon PIXMA Pro9000 Mark II Series, Руководство по обслуживанию

Результаты поиска

Содержание PIXMA Pro9000 Mark II Series

Отзывы:

Бренды по названию

Популярные бренды