manualshive.com logo in svg

Canon PIXMA Pro9000 Mark II Series, Руководство по обслуживанию

Поделиться
Скачать
Canon PIXMA Pro9000 Mark II Series Скачать руководство пользователя страница 55

<Adjustment procedures> 

1)  Without the spur unit, slide the adjustment plate upward (as shown in the left photo) until it slightly 

contacts the eject roller shaft (as shown in the right photo). 
Be cautious not to push up the eject roller shaft. 

2)  Fasten the screws to secure the plate in the adjusted position. 

3)  After adjustment, be sure to perform the service test print, and confirm that no strange noise or faulty 

print operation (uneven printing or print head contacting the paper) occurs.  

 

 

(5)  Ink absorber counter setting 

Before replacement of the logic board, check the ink absorber counter value, and register it to the replaced 

new logic board. (The value can be set in 10% increments.) 

In addition, according to the ink absorber counter value, replace the ink absorber (ink absorber kit). When 

the ink absorber is replaced, reset the applicable ink absorber counter (to 0%). 

- How to check the ink absorber value and the way to set the ink absorber counter: 

See 

4-2. Service Mode, (4) Ink absorber counter setting

. 

 
 

The screws securing the adjustment plate may be loosened only at replacement of the 
platen unit. DO NOT loosen them in other cases. 

<4-3. Grease Application & 4-4. Special Notes on Servicing>

 

52 / 56

Содержание PIXMA Pro9000 Mark II Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды