Canon PIXMA Pro9000 Mark II Series Скачать руководство пользователя страница 22

Страница: 22 / 59

3. REPAIR

3-1. Major Replacement Parts (and Notes on Disassembling / Reassembling)

Pro9000 Mark II

TABLE OF CONTENTS

Service

part

Est.

time

required

(min.)

Recommended removal

procedure / Notes on

replacement

Adjustment / settings

Operation

check

Logic
board
ass'y

(1) External housing
(2) Printer unit
(3) Logic board ass'y

- Before removal of the logic board

ass'y, remove the power cord, and
allow for approx. 1 minute (for
discharge of capacitor's
accumulated charges), to prevent
damages to the logic board ass'y.

- Before replacement, check the ink

absorber counter value (by service
test print or EEPROM information
print).

After replacement:

1. Initialize the EEPROM.
2. Set the ink absorber counter

value.

3. Set the destination in the

EEPROM.

4. Correct the CD / DVD and

automatic print head
alignment sensors.

5. Check the ink system function.
6. Perform LF / Eject correction.

[See

4-2. Service Mode

, for

details.]

7. Perform print head alignment

in the user mode.

- EEPROM

information
print

- Service test

- Printing via

USB
connection

- Direct

printing from
a digital
camera
(PictBridge)

Absorber
kit

(1) External housing
(2) Printer unit
(3) Absorber kit

After replacement:

1. Reset the ink absorber counter.

[See

4-2. Service Mode

, for

details.]

- Ink absorber

counter
value print
(After the
ink absorber
counter is
reset, the
counter
value is
printed
automatically.

Carriage
unit

(1) External housing
(2) Carriage unit
- The screws on the carriage shaft

adjustment plate are allowed to be
loosened only at replacement of
the carriage unit. DO NOT loosen
them in other cases.

At replacement:

1. Before removal of the

carriage shaft, mark the
carriage shaft position.
[See

4-4. Special Notes on

Servicing, (3) Carriage unit
replacement,

for details.]

2. Apply grease to the sliding

portions of the carriage shaft.
[See

4-3. Grease Application

for details.]

- Service test

print
(Confirm ink
system
function.)

19 / 56

Содержание PIXMA Pro9000 Mark II Series




























































Результаты поиска

Содержание PIXMA Pro9000 Mark II Series

Отзывы:

Бренды по названию

Популярные бренды

Canon PIXMA Pro9000 Mark II Series, Руководство по обслуживанию

Результаты поиска

Содержание PIXMA Pro9000 Mark II Series

Отзывы:

Бренды по названию

Популярные бренды