manualshive.com logo in svg

Canon PIXMA Pro9000 Mark II Series, Руководство по обслуживанию

Поделиться
Скачать
Canon PIXMA Pro9000 Mark II Series Скачать руководство пользователя страница 12

2. LIST OF ERROR DISPLAY / TROUBLESHOOTING 

Errors and warnings are displayed by the following ways: 

1. Operator call errors are indicated by the Alarm LED lit in orange, and the error messages are 

displayed by the printer driver Status Monitor.  

2. Error codes (the latest 10 error codes at the maximum) are printed in the "operator call/service call 

error record" area in EEPROM information print  

Buttons valid when an operator call error occurs: 

1. Power button: To turn the printer off and on again.  

2. Resume/Cancel button: To cancel the job at error occurrence, and to clear the error.  

2-1.  Operator Call Errors (by Alarm LED Lit in Orange) 

Pro9000 Mark II 

TABLE OF CONTENTS

Alarm 

LED 

blinking 

in 

orange

Error

Error 

code

U 

No.

Solution

Parts that are likely to 

be faulty

Alarm 
LED lit

Printing from the 
front tray not 
completed.

[1320]

---

Set the paper, and press the 
Resume/Cancel button.

- Platen unit 
- Front door unit 
- Rear tray holder R unit 

2 times 

No paper in the 
rear tray.

[1000]

---

Confirm that the rear tray is 
selected as the paper source. 
Set the paper in the rear tray, 
and press the Resume/Cancel 
button.

- ASF unit 
- Pressure roller unit 
- PE sensor 
- Paper feed motor 

No CD-R tray.

*1

[1001]

---

Set the CD-R tray and press the 
Resume/Cancel button. 

- CD-R tray 
- Carriage unit 

No CD or 

DVD.

*1

[1002]

---

Set a CD or DVD in the CD-R 
tray and insert the CD-R tray in 
the proper position. Then, press 
the Resume/Cancel button. 

- CD-R tray 
- Carriage unit 

3 times

Paper jam.

[1300]

---

Remove the jammed paper or 
foreign material causing a 
paper jam (paper remainings, 
clips, pens, etc.), and press the 
Resume/Cancel button.

- ASF unit 
- Pressure roller unit 
- PE sensor 
- Feed roller  
- Platen unit 

Front tray closed [1250]

---

Open the front tray. (The error 
is indicated when the front tray 
is not opened at start of 
printing, or when the front tray 
is closed during printing.)

- Front door unit 
- Front cover R unit 

Front feed 
support closed

[1260]

---

Open the front feed support. 
(The error is indicated when 

- Rear tray unit 
- Rear tray holder R unit 

9 / 56

Содержание PIXMA Pro9000 Mark II Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды