manualshive.com logo in svg

Canon PIXMA Pro9000 Mark II Series, Руководство по обслуживанию

Поделиться
Скачать
Canon PIXMA Pro9000 Mark II Series Скачать руководство пользователя страница 48

 
 

(3)  LF / Eject correction 

After replacement of the feed roller, platen unit, or logic board  in repair servicing or in refurbishment 
operation, perform the adjustment to maintain the optimal print image quality. (In platen unit replacement, 
apply paper debris over the eject rollers before performing LF / Eject correction.) 

1)  Click 

LF/EJECT

 of the Service Tool on the connected computer, select the paper source, the paper type, 

and whether to feed blank paper. 

- Paper source:  Select 

Rear tray

. 

- Media type:  Select 

PR-201

. 

- Blank paper feed:  Select 

Yes

 when the platen unit is replaced. 

Select 

No

 when the feed roller or logic board is replaced. 

When 

Blank Paper Feed

 is 

Yes

, perform steps 2) to 5). 

When 

Blank Paper Feed

 is 

No

, perform steps 3) to 5). 

2)  Set the following paper in the rear tray, and click 

OK

. The paper will feed. 

- Type:  Plain paper. 

- Size:  A4 or LTR 

- Qty:  15 sheets 

When all sheets (15 sheets) are fed (and the Power LED turns on green), the printer is ready for printing 
the LF / Eject correction pattern. 

3)  Set the following paper in the rear tray, and open the front feed support. 

- Type:  PR-201 (Photo Paper Pro II) 

- Size:  A3+ 

- Qty:  1 sheet 

4)  According to the Blank Paper Feed selection, press the Resume/Cancel button or click 

OK

 in the Service 

Tool. 

- When Blank Paper Feed is 

Yes

, press the Resume/Cancel button of the printer. 

- When Blank Paper Feed is 

No

, click 

OK

 in the Service Tool. 

5)  The LF / Eject correction pattern as shown below is printed while the correction values are automatically 

written to the EEPROM. After the pattern is printed, the printer is ready for selection of another 
function.  

Correction

value setting

(15) Ink Absorber 

Counter 

Ink absorber counter 
setting

See "

Ink Absorber Counter Setting

" below.

(16) Wetting 

Liquid 
Counter 

Wetting liquid counter 
setting

Not used.

45 / 56

Содержание PIXMA Pro9000 Mark II Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды