manualshive.com logo in svg

Canon PIXMA Pro9000 Mark II Series, Руководство по обслуживанию

Поделиться
Скачать
Canon PIXMA Pro9000 Mark II Series Скачать руководство пользователя страница 16

*1:  Only for CD / DVD printing supported regions. 

*2:  Only for CD / DVD printing no-supported regions. 

 

replacing the ink tank(s), press 
the Resume/Cancel button for 5 
sec. or longer to disable the 
function to detect the 
remaining ink amount. After 
the operation, it is recorded in 
the printer EEPROM that the 
function to detect the 
remaining ink amount was 
disabled. 

14 times  Ink tank not 

recognized. 

[1684] U140 A non-supported ink tank (an 

ink tank that is sold in a 
different region from where the 
printer was purchased) is 
installed (the ink tank LED is 
turned off). Install the 
supported ink tanks.

- Ink tank 
- Logic board 
- Carriage unit 

15 times  Ink tank not 

recognized. 

[1682]  U150  A hardware error occurred in 

an ink tank (the ink tank LED 
is turned off). Replace the ink 
tank(s). 

- Ink tank 
- Logic board  
- Carriage unit  

16 times  No ink (no raw 

ink). 

[1688]  U163  Replace the empty ink tank(s),.

Printing with an empty ink tank 
can damage the printer. 
To continue printing without 
replacing the ink tank(s), press 
the Resume/Cancel button for 5 
sec. or longer to disable the 
function to detect the 
remaining ink amount. After 
the operation, it is recorded in 
the printer that the function to 
detect the remaining ink 
amount was disabled.

- Ink tank 
- Logic board  
- Carriage unit 

19 times  Non-supported 

hub. 

[2002]  ---  Remove the applicable USB 

hub from the PictBridge (USB) 
connector.

- DSC harness 
- Logic board 

13 / 56

Содержание PIXMA Pro9000 Mark II Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды