Canon PIXMA Pro9000 Mark II Series Скачать руководство пользователя страница 1

Pro9000 Mark II 
Service Manual 

Revision 0 

 

QY8-13CH-000 

COPYRIGHTc2009 CANON INC. CANON Pro9000 Mark II 031509 XX 0.00-0 

 

Scope 

This manual has been issued by Canon Inc., to provide the service technicians of this product with the information 
necessary for qualified persons to learn technical theory, installation, maintenance, and repair of products. The manual 
covers information applicable in all regions where the product is sold. For this reason, it may contain information that is 
not applicable to your region. 

This manual does not provide sufficient information for disassembly and reassembly procedures. 
Refer to the graphics in the separate Parts Catalog.  

Revision 

This manual could include technical inaccuracies or typographical errors due to improvements or changes made to the 
product. When changes are made to the contents of the manual, Canon will release technical information when necessary. 
When substantial changes are made to the contents of the manual, Canon will issue a revised edition. 

The following do not apply if they do not conform to the laws and regulations of the region where the manual or product is 
used:  

Trademarks 

Product and brand names appearing in this manual are registered trademarks or trademarks of the respective holders. 

Copyright 

All rights reserved. No parts of this manual may be reproduced in any form or by any means or translated into another 
language without the written permission of Canon Inc., except in the case of internal business use. 

Copyright © 2009 by Canon Inc. 
CANON INC. 
Inkjet Device Market Support Management Div.  
451, Tsukagoshi 3-chome, Saiwai-ku, Kawasaki-shi, Kanagawa 212-8530, Japan 

Содержание PIXMA Pro9000 Mark II Series




























































Отзывы: