Canon LBP-1000 Скачать руководство пользователя страница 69

Страница: 69 / 178

B. Fixing and Delivery Unit

The pressure roller and delivery roller in the fixing unit are driven by the main motor (M1001).

The paper separated from the photosensitive drum is fed into the fixing unit by the feed belt.

The toner is fused onto the paper by the fixing film and the pressure roller, and the paper is
delivered from the fixing unit.

The delivered paper is detected by the delivery sensor (PS503). This printer has both a face-

up tray and face-down tray. The paper is usually delivered to the face-down tray, but it switch-
es to the face-up tray when the user opens the face-up tray and pulls it up.

Figure 2-5-3

CHAPTER 2

2 - 35

Photosensitive
drum

Pressure roller

Transfer charging roller

Engine controller PCB

Main motor

DELIVER

DETECTION

signal

(/POSNS)

Face-down delivery rollers

PS503

Feed belts

MAIN

DRIVE

signal

(/MON)

Intermediate PCB

M1001

Face-up tray

Face-down tray

Fixing film unit

Содержание LBP-1000


















































































































































































Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды

Canon LBP-1000, Руководство по обслуживанию

Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды