Canon LBP-1000 Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 178

background image

II. IMAGE DEFECTS

If the factor of the malfunction is identified as “image defects” by the malfunction diagnosis flow-
chart (Figure 4-1-1), find out the cause of the failure according to the table below and clear the
problem.

Table 4-2-1

• II-1

Light:

Output very light image

• II-2

Dark:

Output very dark image

• II-3

Completely Blank:

Output no image

• II-4

All Black:

Output all black paper

• II-5

Dots in Vertical Lines :

Output white dots on the paper

• II-6

Dirt on Back of Paper:

Output dirt on the back of the paper

• II-7

Black Vertical Lines:

Output vertical lines on the paper

• II-8

Black Horizontal Lines:

Output horizontal lines on the paper

• II-9

Dirt:

Output dirt on surface of the paper

• II-10 Blank Spots:

Output image with blank spots

• II-11 White Vertical Lines:

Output white vertical lines on the paper

• II-12 White Horizontal Lines:

Output white horizontal lines on the paper

• II-13 Poor Fixing:

Output the image with poorly fixed toner

• II-14 Image Distortion:

Output distorted image

II-1.

Light

<Possible causes>

1. The image density is not adjusted correctly.

Action:

Adjust the image density by operating the external device.

2. Open the top cover and remove the EP-32 cartridge while printing. Open the drum protec-

tive shield of the cartridge and check the toner image on the photosensitive drum surface.
If the toner image has not been transferred to the paper properly, go to step 3). If the toner
image on the drum is faint, go to step 6).
Do not open the drum protective shield for more than 10 seconds.

3. Deformation or deterioration of the transfer charging roller.

Action:

Replace the transfer charging roller.

4. Poor contact in the transfer charging roller contact on the engine controller PCB and in the

transfer charging roller shaft contact.

Action:

Clean the contacts if dirty. If the problem remains after cleaning, or parts are
deformed or damaged, replace them.

5. Defective engine controller PCB

Action:

Replace the engine controller PCB.

6. Defective laser/scanner unit

Action:

Replace the laser/scanner unit.

7. Defective engine controller PCB

Action:

Replace the engine controller PCB.

CHAPTER 4

4 - 8

«
...
126
127
128
129
130
...
»

Содержание LBP-1000



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LBP-1000

Бренд: Qls Страницы: 53

Бренд: Xerox Страницы: 36

Бренд: Oki Страницы: 16

Бренд: Olympus Страницы: 2

Бренд: WANHAO Страницы: 24

DocuPrint C3055 DX

Бренд: Xerox Страницы: 20

Бренд: zortrax Страницы: 11

Бренд: SEH Страницы: 5

Бренд: Tektronix Страницы: 42

Intelliprint cL160

Бренд: Genicom Страницы: 216

634dte - X B/W Laser

Бренд: Lexmark Страницы: 148

Бренд: Oki Страницы: 132

RepRap Industrial

Бренд: Kuhling&Kuhling Страницы: 24

Accel-a-Writer 4

Бренд: Xante Страницы: 12

Designer XL PRO

Бренд: PICASO 3D Страницы: 72

Бренд: Hitachi Страницы: 11

Бренд: Hitachi Страницы: 62

Бренд: Hitachi Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды