Canon LBP-1000 Скачать руководство пользователя страница 101

Страница: 101 / 178

H. Transfer Charging Roller

1) Open the top cover.
2) Unhook the claw of the left bushing of

the transfer charging roller. Lifting the
roller slightly, remove the right side of
the shaft from the bushing. Remove
the transfer charging roller.

➀

Bushings

➁

Transfer charging roller

Figure 3-4-10

< Notes for reassembly >

When installing the roller, hold the shaft
and bushing, not the sponge area, of the
transfer charging roller.

When the roller is set, insert the spring

into the boss of the bushing securely so
that the bushing pushes the spring.

Figure 3-4-11

Fixing Film Unit

1) Remove the fixing unit according to the

steps 1) through 3) on page 3-9.

2) Disconnect the connector from the

delivery sensor.

3) Remove the cables from the guides.

➀

Connector

➁

Cables

Figure 3-4-12

4) Remove the 2 screws.
5) Unhook the 2 claws, and then remove

the cover.

➀

Screws

➁

Claws

➂

Cover

Figure 3-4-13

Note:

In the procedure 5), use care when
unhooking the 2 claws. The cover
springs up due to the spring ten-
sion.

CHAPTER 3

3 - 14

Shaft

Bushing

➂

➀

➁

➀

➁

➀

➁

➀

Содержание LBP-1000


















































































































































































Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды

Canon LBP-1000, Руководство по обслуживанию

Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды