Canon LBP-1000 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 178

background image

V. PICK-UP/FEED SYSTEM

A. Outline

Presence of paper on the multi-purpose tray is detected by the multi-purpose tray paper sensor
(PS504). Presence of paper in the cassette is detected by the cassette paper sensor (PS501).

When a print instruction command is input to the engine controller from the video controller,

the main motor (M1001) and scanner motor start rotating and the fixing heater temperature
control starts.

The cassette pick-up solenoid (SL501) or multi-purpose tray pick-up solenoid (SL502) is

turned ON when the following three requirements are met.
1) After the main motor has been driven for 0.5 seconds.
2) In case of paper pick-up from the cassette, after the scanner motor has reached 80% of the

specified rotation number for 0.6 seconds, and for 1.1 seconds in case of paper pick-up from
the multi-purpose tray.

3) The fixing heater temperature has been brought to the specified temperature by the initial

temperature control, or the specified period of time has elapsed after start of the tempera-
ture control.

In case of paper pick-up from the cassette, SL501 is turned ON, and the rotation of the main
motor is transmitted to the cassette pick-up roller. The cassette pick-up roller makes a rotation,
and paper in the cassette is picked up. In case of paper pick-up from the multi-purpose tray,
SL502 is turned ON, and the tray cam rotates to lift the tray loaded with paper so that the paper
makes contact with the multi-purpose tray pick-up roller. At the same time, the multi-purpose
tray pick-up roller makes a rotation to pick-up a sheet of paper from the multi-purpose tray.

The paper is separated from any excessive sheets of paper by the separation pad and fed to

the registration roller.

•

Paper pick-up timing

Figure 2-5-1

CHAPTER 2

2 - 32

Print instruction command

Main motor (M1001)

Scanner motor

Cassette pick-up solenoid (SL501)

Multi-purpose tray pick-up solenoid (SL502)

Top-of-page sensor (PS502)

Fixing heater

(Unit: second)

STBY

INTR

PRINT

0.6

1.1

80% of the specified rotation number

«
...
64
65
66
67
68
...
»

Содержание LBP-1000



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LBP-1000

ImageCLASS MF4570dw

Бренд: Canon Страницы: 164

imagePRESS C800 Series

Бренд: Canon Страницы: 132

ImageCLASS MF5730

Бренд: Canon Страницы: 2

Бренд: Panasonic Страницы: 102

Бренд: EasyThreed Страницы: 15

Бренд: TallyGenicom Страницы: 3

Бренд: Radio Shack Страницы: 62

Бренд: Chamjin I&C Страницы: 21

Бренд: Olivetti Страницы: 16

Бренд: Oki Страницы: 40

Бренд: Felix printers Страницы: 26

Бренд: Oce Страницы: 268

ProJet x60 Series

Бренд: 3D Systems Страницы: 72

Бренд: Lexmark Страницы: 13

8560MFPD - Phaser Multifunction Printer Color Laser

Бренд: Xerox Страницы: 20

Бренд: Olivetti Страницы: 293

Бренд: Konica Minolta Страницы: 8

Бренд: Savin Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды