Canon LBP-1000 Скачать руководство пользователя страница 174

Страница: 174 / 178

APPENDEX

A - 12

Message

Action

Meaning

FLASH ERROR

FLASH FORMAT

RESTART

FLASH

FORMATTING...

READY

FLUSHING...

5F-50 ERROR

CALL FOR SERVICE

5F-51 ERROR

CALL FOR SERVICE

5F-52 ERROR

CALL FOR SERVICE

5F-59 ERROR

CALL FOR SERVICE

6F-61 ERROR

CALL FOR SERVICE

6F-63 ERROR

CALL FOR SERVICE

6F-68 ERROR

CALL FOR SERVICE

6F-7A ERROR

CALL FOR SERVICE

PS OPTION

ERROR

PARALLEL1

INTERFACE ERROR

PARALLEL2

INTERFACE ERROR

OPTION RAM

ERROR

OPTION ROM

ERROR

COLD RESET

CONTEXT SAVE

ADJUSTED

An error has occurred when trying to format,

or read or write data to the optional Flash

ROM.

The optional Flash ROM has been formatted

using the FORMAT FLASH item. The print-

er will restart.

The optional Flash ROM is being formatted.

A Cancel job is performed while the printer

is receiving data or while the printer is in the

middle of printing a job.

Fixing unit malfunction

BD malfunction

Scanner unit malfunction

Cooling fan malfunction

Resident ROM checksum error

Resident DRAM error

NVRAM (EEPROM) error

SRAM in AIR chip error

An optional ROM DIMM diagnostic error.

The parallel port is not communicating with

the controller.

The parallel port is not communicating with

the controller.

Option DRAM DIMM diagnostic error.

An option DRAM DIMM has failed the start-

up diagnostic check.

Option ROM DIMM diagnostic error.

An option ROM DIMM has failed its startup

diagnostic check.

Displays when the COLD RESET Power-On

sequence is selected.

The context saving items (PCL SAVE or PS3

SAVE) in the MEMCONFIG MENU have been

adjusted automatically by the printer oper-

ating system. This message is displayed

when printer has been turned ON with con-

text saving feature enabled, but due to man-

ual changes to the operation panel, there is

Replace the Flash ROM.

No action required.

The printer is flushing the job.

Perform the troubleshooting pro-

cedure described in Section VI of

Chapter 4.

No action required although the

printer will be reset to its factory

defaults and any unique settings

will have to be reset.

Press Go key to continue.

Содержание LBP-1000


















































































































































































Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды

Canon LBP-1000, Руководство по обслуживанию

Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды