Canon LBP-1000 Скачать руководство пользователя страница 173

Страница: 173 / 178

IV. MESSAGES TABLE

APPENDEX

A - 11

Message

Action

Meaning

READY

PAUSED

RESET TO SAVE

MEMORY OVER-

FLOW

PRINTING...

+ FORMAT FLASH

- IGNORE FLASH

+ REALLY FORMAT

- IGNORE FLASH

FLASH OVERFLOW

The printer is ready to receive data and

print.

The printer is off-line.

RESET verification prompt.

This message appears momentarily and then

PAUSED. When a menu item was changed

before the printer releases the port on which

the last job was processed, such as in the

middle of a job, or before the port timed out.

A memory overflow has occurred.

The printer received more data than it can

hold in the available memory on the printer.

This can occur if too many soft fonts,

macros, or complex graphics are sent to the

printer.

Usually displayed when printing an item

from the TEST MENU, or when attempting to

go off-line while the printer is busy.

The FORMAT FLASH item is selected to for-

mat the optional Flash ROM.

The operator is being asked to verify the

Flash ROM formatting is really wanted. This

is in response to the foregoing message.

A memory overflow has occurred in the

optional Flash ROM

The printer has received more font and

macro data than it can hold in the available

memory of the Flash ROM. The printer goes

off-line when this message is displayed.

No action required.

Press Go key.

Two options are available:

1. Press Shift+Enter key to enter

the RESET menu and save the

information immediately. This

will terminate the current job,

deleting temporary fonts, macros

and buffered data.

2. Press Go key and the current

job will resume where it left off.

The menu items changed will not

take effect until the next end of

job.

The job will resume after 10 sec-

onds if AUTOCONT is ON.

Otherwise press the Go key to

resume printing. Check the page

that ejects since the page could

not be processed as requested.

Also simplify the job or add addi-

tional memory.

No action required.

(press Value key) to for-

mat the Flash ROM. Select -

(press Shift and Value keys) to

cancel the operation.

For new/unformatted Flash

ROM: the printer will automati-

cally format the Flash ROM with-

out any message display when

the printer is warming up.

(press Value key) to veri-

fy that the Flash ROM is to be

formatted. Select - (press Shift

and Value keys) to cancel the

operation.

Press the Go key to take the

printer back on-line.

Format the Flash ROM or delete

font and macro data to create

more space.

Содержание LBP-1000


















































































































































































Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды

Canon LBP-1000, Руководство по обслуживанию

Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды