Canon LBP-1000 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 178

background image

applied to the back of the paper, they may be dispersed at fixing.

This printer applies the negative DC voltage to the fixing film via the pressure roller shaft

(pressure roller shaft is a mere continuity path). The negative charge is applied to the paper sur-
face by the fixing film. This improves the adhesion force of the toner particles to the paper and
prevents dispersion of the toner particles.

This printer utilizes an on-demand method which uses fixing film with small heat capacity.

This method has fast temperature rising time and it is not necessary to supply power to the fix-
ing heater during the STANDBY mode. Wait time of less than 10 seconds and energy conserva-
tion are made possible by this method.

Fixing film is cylindrical film of polyimide. Its surface is coated with fluorine to prevent off-

set.

5. Drum cleaning block

In the transfer block, not all the toner is transferred to the paper, but some remains on the pho-
tosensitive drum.

In this block, the residual toner is cleaned off so that the next print image will be clear and

distinct.

Step 7: Drum cleaning

Figure 2-4-13

The residual toner on the drum surface is scraped away with the cleaner blade to clean the drum
surface in preparation for the next print. The removed toner is collected in the waste toner case.

CHAPTER 2

2 - 31

Waste toner case

Cleaner blade

Sweeper strip

Photo-

sensitive

drum

«
...
63
64
65
66
67
...
»

Содержание LBP-1000



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LBP-1000

Бренд: Oki Страницы: 222

Бренд: Oki Страницы: 4

Бренд: Oki Страницы: 160

Бренд: IBM Страницы: 60

Бренд: Citizen Страницы: 80

Бренд: BIXOLON Страницы: 59

Бренд: Lexmark Страницы: 4

Бренд: Ricoh Страницы: 2

Бренд: Oki Страницы: 187

LaserPro StellarMark IFII Series

Бренд: GCC Technologies Страницы: 111

634dte - X B/W Laser

Бренд: Lexmark Страницы: 148

Бренд: SPRT Страницы: 48

5470 - X Color Inkjet

Бренд: Lexmark Страницы: 202

Бренд: Ricoh Страницы: 12

Бренд: Pringo Страницы: 2

Бренд: Riso Страницы: 150

Бренд: Ricoh Страницы: 678

Бренд: Oki Страницы: 239

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды