Canon LBP-1000 Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 178

background image

B. Initial Check

Check the following items before making a diagnosis of malfunction. If any failure is found, the
service technician is to clear the problem and to give the instruction to the user.

1. Installation environment

Make sure that the requirements stated below meet when installing printer:
a. The line voltage is from -10% to +6% of the rated voltage.
b. The printer is securely installed on a level surface.
c.

The room temperature is kept between 10

°

C and 32.5

°

C, and the relative humidity, between

20% and 80%.

d. Avoid sites generating ammonia gas, high temperature or high humidity (near water faucet,

kettle, humidifier), cold places, open flames and dusty areas.

e.

Avoid sites exposed to direct sunlight. If unavoidable, advise the customer to hang curtains.
Lights should not be placed especially on the multi-purpose tray side.

f.

A well-ventilated place.

g. Make sure that the power plug is inserted to the printer and the outlet securely.

2. Paper checks

a. The recommended paper for this printer is used.
b. The paper is not damp.

3. Paper sets

a. The paper is set to the pick-up source within the specified volume.
b. The paper is set to the selected pick-up source correctly.
c. The cassette is installed in the printer correctly.
d. The size plate and the end plate (cassette only) are set correctly according to the paper size.

4. EP-32 cartridge sets

The cartridge is installed in the printer correctly contacting with the back of the slot firmly.

5. Condensation

During winter, particularly when moving the printer into a warm room from a cold location such
as a warehouse, various problems can occur due to condensation in the printer.

Example)

a. Condensation in the optical system (six-faced mirror, reflecting mirror, lens, etc.) will result

in light output images.

b. As the photosensitive drum is cold, the resistance of the photoconductive layer is high. This

will lead to incorrect contrast.

If condensation appears, either wipe the parts with dry cloth, or leave the printer ON for 10 to
20 minutes.

If an cartridge is opened soon after being moved from a cold room to a warm room, conden-

sation may appear inside the cartridge and may cause various image defects.

Be sure to instruct the customer that it is necessary to leave the cartridge sealed for one to

two hours at room temperature to allow it to acclimatize.

CHAPTER 4

4 - 4

«
...
122
123
124
125
126
...
»

Содержание LBP-1000



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LBP-1000

Бренд: Felix Storch Страницы: 39

Бренд: Felix Storch Страницы: 10

Бренд: Xerox Страницы: 23

Бренд: IBM Страницы: 113

Бренд: IBM Страницы: 16

Бренд: IBM Страницы: 214

Бренд: iFactory3D Страницы: 39

Бренд: Valentin Страницы: 96

Бренд: Oki Страницы: 197

Бренд: Roland Страницы: 44

Бренд: TierTime Страницы: 28

Бренд: TRENDnet Страницы: 14

Бренд: TP-Link Страницы: 16

Бренд: Felix Storch Страницы: 46

Falcon Outdoor 46

Бренд: MUTOH Страницы: 333

Бренд: Magicard Страницы: 124

Бренд: Oki Страницы: 143

Бренд: Konica Minolta Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды