Canon LBP-1000 Скачать руководство пользователя страница 135

Страница: 135 / 178

III-1. Multi-purpose tray pick-up block

<Possible causes>

1. Defective video controller PCB

Action:

Make an engine test print from the Multi-purpose tray. If the printer feeds the
paper normally, replace the video controller PCB.

2. Curled paper

Action:

Straighten the paper, and then instruct the user.

3. Dirty, worn, or deformed multi-purpose tray pick-up roller

Action:

Clean the pick-up roller if dirty. Replace it if worn or deformed.

4. Spring of the tray is out of place or defective

Action:

Set the spring in the right position. Replace it if defective.

5. Worn or damaged tray cam

Action:

Replace the cam.

6. Damaged gear

Action:

Replace the gear.

7. Defective multi-purpose tray pick-up solenoid

Action:

Disconnect the multi-purpose tray pick-up solenoid connector J404 from the engine
controller PCB. Measure the resistance between the cable side connector J404-1
and J404-2. If it is not about 95

Ω

, replace the multi-purpose tray pick-up solenoid.

8. Poor contact in the main motor drive signal line connector

Action:

Reconnect the main motor connector J1702 and the intermediate PCB connector
J1007 correctly.

9. Defective main motor

Action:

Replace the main motor.

10. Poor contact in the engine controller PCB connector.

Action:

Reconnect the engine controller PCB connector J401 correctly.

11. Defective engine controller PCB

Action:

Replace the engine controller PCB.

III-2. Cassette pick-up block

<Possible causes>

1. Defective video controller PCB

Action:

Make an engine test print from the paper feeder. If the printer feeds the paper nor-
mally, replace the video controller PCB.

2. Dirty, worn, or deformed cassette pick-up roller

Action:

Clean the roller if dirty. Replace it if worn or deformed.

3. Damaged gear

Action:

Check the gears of the cassette pick-up unit and feed roller. Replace any damaged

CHAPTER 4

4 - 15

Содержание LBP-1000


















































































































































































Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды

Canon LBP-1000, Руководство по обслуживанию

Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды