Canon LBP-1000 Скачать руководство пользователя страница 176

Страница: 176 / 178

APPENDEX

A - 14

Message

Action

Meaning

PAGES: ####

PAPER JAM

WRONG PAPER

SIZE

PRINTER OPEN

RESETTING PRINT-

KEY NOT VALID

WARMING UP...

MENU, where #### is the total number of

pages.

A paper jam has occurred in the printer.

A paper size mismatch has occurred. There

is a mismatch between the physical paper

size and the paper size requested by the job.

Printer is open.

This message is displayed when RESET

=PRINTER is selected in the RESET MENU.

This message is displayed when a key that is

not enabled in the current function is

pressed.

The printer is warming up.

No action required.

Remove the jammed paper. The

top cover must be opened and

closed to resume printing.

Inspect the tray or the cassette

for mismatched paper and cor-

rect.

Close the printer.

No action required.

Press the correct key to complete

the current function.

Wait until the printer has warmed

up and displays READY.

Содержание LBP-1000


















































































































































































Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды

Canon LBP-1000, Руководство по обслуживанию

Результаты поиска

Содержание LBP-1000

Отзывы:

Похожие инструкции для LBP-1000

Бренды по названию

Популярные бренды