![background image](http://html.mh-extra.com/html/canon/dr-6080/dr-6080_service-manual_62889033.webp)
COPYRIGHT © 2003 CANON ELECTRONICS INC. CANON DR-6080/9080C REV.0 SEPT. 2003
2 - 9
CHAPTER 2 FUNCTIONS & OPERATION
2. Reading Unit Configuration
Fig. 2-204 is a sectional diagram of the
reading unit. The reading unit consists of the
sensor drive PCB, image sensor PCB, lens array,
LEDs (R/G/B), light guide, and reading glass.
The contact image sensors (CIS) are mounted
on the image sensor PCB in a single row, with a
density of 600 dpi. The valid reading width is 305
mm, and the number of valid pixels is 7260. The
optical resolution can be switched between 600 dpi
and 300 dpi by an external signal.
The main feature of this reading unit is that it
provides lighting for the image sensors using two
LEDs, lighting the document from both the right
and left sides as shown in the figure. The light
guides are arranged on the right and left side, and
a red (R), green (G), and blue (B) LED is arranged
for each light guide on the image sensor PCB.
LEDs light illuminate the document through
the light guides, and the light reflected from the
document enters the image sensors through the
lens array. The image sensors convert the light to
an analog signal. The analog signal is sent to the
sensor drive PCB, and then to the main CPU PCB
as a digital signal after A/D conversion and
shading correction.
In the binary or grayscale mode, the image is
read with composite light generated by lighting all
the RGB LEDs simultaneously. In the color mode,
the RGB LEDs are sequentially lit, and the image
data is read separately for each color. In the
drop-out color mode, only the LEDs of the
designated color are lit.
In the previous models (DR-5020/5080C), A/D
conversion and shading correction were handled
by the image processor on the main CPU PCB, but
in this model they are processed internally by the
reading unit.
Reading glass
Sensor drive PCB
Image sensor
PCB
Image sensor (CIS)
Light guide
Light guide
Lens array
LEDs (R/G/B)
LEDs (R/G/B)
Document
Fig. 2-204
Содержание DR-6080
