![background image](http://html.mh-extra.com/html/canon/dr-6080/dr-6080_service-manual_62889159.webp)
COPYRIGHT © 2003 CANON ELECTRONICS INC. CANON DR-6080/9080C FIRST EDITION OCT. 2003
5 - 9
CHAPTER 5 TROUBLESHOOTING
5) The Service window appears.
6) To exit from the service mode, select "Close"
in the Service window.
When turning on the personal computer for
service after this machine has been connected, a
window appears to ask for the installation of 'new
hardware' or a 'device driver.' In this case, take the
following action:
a) When only the service mode software has
been installed, click 'Cancel'.
b) When the driver bundled with the machine has
been installed, follow the user’s manual.
Note:
When performing service modes using the
user's personal computer, make sure that
the program "\Driver\Tools\QumaTool.exe"
is launched from the bundled Setup disk.
Do not copy the QumaTool.exe file onto the
user's personal computer. When starting
any service mode, pay attention not to
reveal the folder name or password to the
user.
4. Regist
This mode is used to adjust registration for
image scanning.
1) Set some plain white copy paper (A4/LTR) on
the document tray.
Note:
Do not use dirty or creased paper. Place the
sheets along the document guide so that
they are not skewed.
2) Select “Regist” from the Service window.
The state-displaying window appears (Refer
to Fig.5-304).
When the registration adjustment is
completed the state-displaying window
disappears and the service window appears.
Fig. 5-304
Note:
If this mode is executed with no document
loaded, an error window (See Fig. 5-305)
appears. Load a document and click OK to
continue the registration adjustment.
Fig. 5-305
Содержание DR-6080
