Canon Colorado 1630 Скачать руководство пользователя страница 375 | Manualshive

Страница: 375 / 388

Canon Colorado 1630 Скачать руководство пользователя страница 375

Conformity declaration for Radio devices (USA and Canada)

• This equipment contains a certified modular transmitter. The modular transmitter is located in

the

ink supply unit

and can only be accessed by a service technician.

• The transmitter’s FCC ID is

2AGNM

, the IC ID is

22117

.

Conformity declaration for Federal Telecommunications Law (Mexico)

This end device contains an RFID module which is already approved by IFETEL
(RCPOCOC16-1941) for Federal Telecommunications Law.

Conformity declaration for Telecommunications (Hong Kong)

This end device contains an RFID module which is already approved by ISM (HKCA1035, issue 7)
for the Communications Authority. Certificate No.: HK0011801838.

Conformity declaration for Telecommunications (Malaysia)

This end device contains an RFID module which is already approved by MCMC MTSFB (TC
T007:2014) for Communications and Multimedia Act. Approval No.: RCCV/24A/0418/S(18-1613).

Conformity declaration for Telecommunications (Singapore)

This end device contains an RFID module which is registered with the Info-communications
Media Development Authority under regulation 20(6) of the Telecommunications (Dealers)
Regulations (Cap 323, Rg 6) (the "Dealers Regulations") and approved for sale in Singapore.
Telecommunications (Amendment) Act 2011 (No. 19 of 2011).

Conformity declaration for Telecommunication (Indonesia)

This end device contains an RFID module which is certified by the ministry of communications
and information technology, directorate general of resources and equipment for post and
information technology, the republic of Indonesia. Telecommunication Law No.36 of 1999.

Appendix A - Regulation Notices

375

«
...
373
374
375
376
377
...
»

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды