manualshive.com logo in svg

Canon Colorado 1630, Руководство по эксплуатации

Поделиться
Скачать
Canon Colorado 1630 Скачать руководство пользователя страница 305

Field

Description

jobid

Unique job ID that is generated by the controller each time a new job is created.

NOTE

In case of controller reinstallation, software error, or power failure it
cannot be guaranteed that the ID is unique.

jobtype

The value AP (Automatic Print Jobs) is used for all jobs from the RIP, so the value
is always AP.

jobname

The name of the job specified in the RIP.

printmode

The name of the print mode that was used in the job.

startdate

<yyyy><mm><dd> The date the printer starts printing the job.

starttime

<hh>:<min>:<ss> The time the printer starts printing the job.

activetime

<num>:<min>:<ss> The total time the job is active and printing. This time in-
cludes autonomous maintenance actions. Note that the time needed for warming
up before the printer is ready and the time spend waiting for the operator, e.g. to
solve an error, is not included. Time in hours, minutes, seconds, where hours can
exceed 24.

idletime

<num>:<min>:<ss> The total time an active job is waiting for operator interac-
tion, e.g. solving an error or loading media. Time in hours, minutes, seconds,
where hours can exceed 24.

readydate

<yyyy><mm><dd> The date a job is completed successfully, canceled or deleted.

readytime

<hh>:<min>:<ss> The time a job is completed successfully, canceled or deleted.

accountid

This field is always empty.

noffinished-
sets

<num> The number of times the bitmap, as received by the RIP, has been prin-
ted.

NOTE

This number can be lower than 'copiesrequested' as the user can can-
cel or delete a job.

result

'Done', 'Abrt', 'Stop', 'Deleted'. The state in which the job was completed.
• 'Done': when the job was completed successfully.
• 'Abrt': when the job was started, but aborted by the operator or controller due

to an error.

• 'Stop': when the job was started, but stopped or paused by the operator.
• 'Deleted': when the job was deleted before it was printed.

reception-
date

<yyyy><mm><dd> The date the printer controller completely received the job
from the RIP.

reception-
time

<hh>:<min>:<ss> The time the printer controller completely received the job
from the RIP.

operator-
note

Note information specified in the RIP.

copies re-
quested

<num> The number of copies requested by the RIP.

mediatypeid The media type ID specified in the RIP that is used to communicate to the printer

which media it has to use.

4

Download an account log file

Chapter 9 - Troubleshooting and support

305

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды