Canon Colorado 1630 Скачать руководство пользователя страница 255

Страница: 255 / 388

List of Colorado 1630 maintenance materials

Items to order

The items listed below can be requested from your local representative:

Maintenance material

Used for

Prescribed Microflex
gloves

Handling Colorado 1630 UVgel ink.

Lint free cloth

Cleaning the printer when polluted with ink.

Prescribed Swabs

Cleaning pollution on surfaces such as the maintenance station,
wiper and clean wall, matrix plate etc.

Matrix plate cleaning tool

Cleaning the matrix plate (holder).

Matrix plate cleaning foam Cleaning the matrix plate (foam to put in the holder).

Cleaning liquid (Cleaner
MB - methyl benzoate)

Cleaning ink pollution on heated surfaces: the matrix plate, wiper
and clean wall only. Used only with swabs.

IMPORTANT

This cleaning liquid is not used for any other parts in the
printer.

Maintenance tray

Replacing a full maintenance tray.

Wiper

Replacing the wiper.

UVgel ink (CMYK)

Refilling new ink.

Set of foams

Replacing polluted guide plate foams.

Roller assy

Replacing a polluted guide plate roller assy.

Filters

Replacing saturated filters.

Bracket with two lubrica-
tors and pins

Replacing the lubricators.

Xtran pinch rollers

Replacing the rollers of the Xtran pinch.

Knife

Replacing a blunt embedded knife.

Tension bar

Replacing a tension bar that has been damaged or lost.

Drive gear

Replacing a drive gear that has been damaged on a media shaft.

Items provided once

The items listed below are delivered only once, together with the machine at installation:

Maintenance material

Used for

Screwdriver (Torx-25)

Opening the chiller cover and the knife compartment cover.

Pouring can

Refilling demineralized water in the chiller.

Items to provide yourself

The items listed below you should provide yourself:

List of Colorado 1630 maintenance materials

Chapter 6 - Maintain the system

255

Содержание Colorado 1630





































































































































































































































































































































































































Результаты поиска

Содержание Colorado 1630

Отзывы:

Бренды по названию

Популярные бренды

Canon Colorado 1630, Руководство по эксплуатации

Результаты поиска

Содержание Colorado 1630

Отзывы:

Бренды по названию

Популярные бренды