Canon Colorado 1630 Скачать руководство пользователя страница 311

Страница: 311 / 388

Configure, upload and install operating system updates from a file

Introduction

This topic describes how to configure, upload and install operating system updates from a file via
the Settings Editor.

The downloaded operating system update package is cumulative. This means that the package
includes all preceding patches.

NOTE

This procedure applies only to operating system updates that are manually uploaded in the

Settings Editor.

Approach

The operating system updates can be downloaded via:

https://downloads.cpp.canon/

The operating system updates consist of multiple files. This is called an update package. All files
must be installed.

The file names start with MSU followed by a 5-digit number. The files must be installed in
ascending order based on this number.

IMPORTANT

From software version

Mark 8.1.3

, updates can be installed simultaneously in any order. If your

system has a lower Mark version, you must install the files in the correct order. You can check

the software version in the Settings Editor via [Support]

→

[About]

→

[Version of software].

During the installation of the operating system updates the printer remains operational. To
finalize the installation, you must restart the system.

Before you begin

• You must be logged in as a system administrator.
• Download the operating system update package for the [Version of printer software] of your

printer via

https://downloads.cpp.canon/

Configuration of operating system updates from a file via the Settings Editor

1. Open the Settings Editor and go to: [Support]

→

[Software updates].

2. Go to [Operating system updates].
3. Click [Configure].

4. Use the [Installation moment] to select the installation time.

Configure, upload and install operating system updates from a file

Chapter 9 - Troubleshooting and support

311

Содержание Colorado 1630





































































































































































































































































































































































































Результаты поиска

Содержание Colorado 1630

Отзывы:

Бренды по названию

Популярные бренды

Canon Colorado 1630, Руководство по эксплуатации

Результаты поиска

Содержание Colorado 1630

Отзывы:

Бренды по названию

Популярные бренды