Canon Colorado 1630 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 388

Canon Colorado 1630 Скачать руководство пользователя страница 24

Installation

WARNING

• The machine may be transported, assembled, installed, moved and repaired only by an

authorized service representative.

• The installation of accessories and options not permitted for the machines may constitute a

violation of the Safety Regulations and Directives, and can also damage the machine.

• Consult your authorized service representative for details on which accessories and options

are permitted for the machine.

• Only use cables specified by the manufacturer.
• Place the machine on a horizontally level surface of sufficient support.
• Do not place the machine in a location that is subject to vibrations and shocks.
• Do not use flammable sprays, liquids or gases near the product as this can cause fire.

Space requirements and operation precautions

WARNING

• The machine must be connected to an air exhaust (to the outside atmosphere) or must

contain the filters and proper room ventilation for keeping the chemical emission below the
limits. See the Product Safety Data Sheet (PSDS) for the ventilation recommendations.

• For keeping the chemical emission below the limits do not place the machine in a room

which is too small or insufficiently ventilated. See the Product Safety Data Sheet of the
machine for the ventilation recommendations.

Operation

WARNING

• Do not lean, lie or stand on any part of the machine, including parts that can be pulled

outwards (e.g. media drawers).

• Read the User Documentation carefully before operating the machine. In case of any

questions or uncertainties regarding the content of this document, contact your authorized
sales or service representative.

• Make sure that no objects (e.g. jewelry chains, paper clips, coins) or liquids can get into the

interior of the machine. Do not place containers with fluid on top of or near the machine.

• Disconnecting the product from the mains-supply network (unplug, power-switch) might

result in damage to the system.

• Do not open any door when the machine is starting up or running, unless the control panel

displays a message that asks you to open one or more doors.

• If you operate the machine remotely, make sure that nobody is working on the machine.

CAUTION

• This equipment is not suitable for use in locations where children are likely to be present.

Safety and Environment Information

24

Chapter 2 - Safety information

«
...
22
23
24
25
26
...
»

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды