manualshive.com logo in svg

Canon Colorado 1630, Руководство по эксплуатации

Поделиться
Скачать
Canon Colorado 1630 Скачать руководство пользователя страница 229

Procedure

1.

Move to the media input side and open the top cover.

2.

Put on the Colorado 1630 approved gloves.

3.

Carefully push the printhead carriage to the left in manual maintenance position (1).

IMPORTANT

Touch the printhead carriage on the covered area only, otherwise you can damage the
printheads.

4.

Take a piece of paper and place it under the Xtran roller you want to replace (2).

5.

Remove the black clamp from the axis.
Use the small screwdriver to push the black plastic part of the axis on both sides away from the
unit.
Only push at the top of the plastic part otherwise you will break the axis holder.

Replace the rollers of the Xtran pinch

Chapter 6 - Maintain the system

229

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды