manualshive.com logo in svg

Canon Colorado 1630, Руководство по эксплуатации

Поделиться
Скачать
Canon Colorado 1630 Скачать руководство пользователя страница 25

Maintenance, repair and modification

WARNING

• Do not modify the machine. Modifying the machine can cause a hazard like fire, electrical

shock or other injuries or jeopardize given warranties.

• Only perform maintenance activities as described in the User Documentation.
• Only instructed or skilled persons are allowed to maintain the machine, to avoid any risk and

not to jeopardize given warranties.

• Do not bridge or disable any safety interlock devices. Disabling or otherwise defeating safety

interlock devices will cease their function as safety guard and may create hazardous
conditions for all people operating the machine.

CAUTION

• Repairs to the machine may only be performed by authorized service representatives.
• Service areas may only be opened by authorized service representatives. Do not remove

covers and panels that are fixed to the machine. Some parts of the machine may have a
hazardous electrical component, hazardous heat source or a laser beam source inside that
could cause an electrical shock or other injuries.

Relocation of the machine

CAUTION

• Disconnect the power cord and other cables before you move the machine.
• Only skilled person(s) are allowed to move the machine.

Actions in response to problems

WARNING

• In case smoke and/or fire is noticed:

• Immediately try to close in a safe way all machine covers and doors so that the smoke or

fire stays within the enclosure of the machine. Prevent personal injury during closing of
these doors and covers.

• Immediately cut of the electrical power to the machine by disconnecting the mains plug or

proper disconnecting device. Make sure that the machine cannot be switched on any
more.

• Immediately inform the emergency response services.

Poisonous gases can be produced in any fire. They can also result from a fire in this machine.
Keep into account: Canon Production Printing systems are designed in such a way that fire is
encapsulated within the enclosure, thus preventing the further spread of fire to the
customer’s premises.

• In case of damage to the covers, power cable, operating elements, or in case of penetration

of fluids or foreign bodies, disconnect the machine from the power supply and contact your
authorized service representative.

Safety and Environment Information

Chapter 2 - Safety information

25

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды