Campbell NL240 Скачать руководство пользователя страница 47

Страница: 47 / 74

Appendix B. Cables, Pinouts, LED

Function, and Jumper

B.1 CS I/O

The CS I/O cable is a 9-pin, straight-through cable with all 9 pins connected.

The supplied SC12 cable (pn 16675) is recommended.

TABLE B-1. CS I/O Pinout

Pin

Datalogger (DB9 Female)

Function

Peripheral (DB9 Male)

Function

5 VDC

N/C

SIGNAL GND

RING

RXD

TXD

SDE

CLK/HS

12 VDC (output)

12 VDC (input)

TXD

RXD

B.2 RS-232

A DB9 female to DB9 male cable (such as Campbell Scientific part number

10873) is used to connect the NL240’s RS-232 port to the datalogger’s RS-232

port. The supplied SC12 cable can also be used. A DB9 female null modem

cable (such as Campbell Scientific part number 13657) is used to connect the

NL240’s RS-232 port to a PC’s RS-232 port. The RS-232 cable should be kept

short when using high baud rates.

TABLE B-2. RS-232 Pinout

Pin

Datalogger (DCE, DB9 Female)

Function

Peripheral (DTE, DB9 Male)

Function

DCD

TXD

RXD

TXD

DTR

SIGNAL GND

DSR

CTS

RTS

CTS

RING

B-1

Содержание NL240











































































Результаты поиска

Содержание NL240

Отзывы:

Похожие инструкции для NL240

Бренды по названию

Популярные бренды

Campbell NL240, Инструкция по эксплуатации

Результаты поиска

Содержание NL240

Отзывы:

Похожие инструкции для NL240

Бренды по названию

Популярные бренды