Campbell NL240 Скачать руководство пользователя страница 23

Страница: 23 / 74

NL240 Wireless Network Link Interface

After the NL240 has joined a network, the green LED will flash with network

activity. If the NL240 is configured for DHCP, the green LED will blink once

a second while it is attempting to acquire a network address from DHCP.

Operating System Upgrade

When a new operating system is sent to the NL240, the red LED will blink

repeatedly while the NL240 copies the operating system into its internal flash.

This process takes about 10 seconds. While the LED is blinking, the NL240 is

in a vulnerable state where a removal of power will leave the NL240 without a

valid operating system. Do not remove power until the LED stops blinking.

If an operating system upgrade includes an upgrade to the internal Wi-Fi

module’s firmware, after the typical re-flashing and blinking of the red LED,

the device will power up and start copying the new firmware to the Wi-Fi

module. The red LED will also blink during this process. It will start out as a

slow blink and get faster and faster as the process nears completion. This

process can take around 1.5 minutes. Again, do not remove power until the

LED stops blinking.

7. Configuring the NL240

The NL240 is configured using

DevConfig

version 2.03 or greater. You can

connect your NL240 to

DevConfig

using either a Wi-Fi connection or USB.

7.1 Configuring the NL240 with

DevConfig

via USB

INSTALL the DEVICE DRIVER BEFORE plugging the NL240

into your PC for the first time. You will need the device driver

properly installed before you can connect to the NL240 via USB.

To install the device driver, download the latest version of

DevConfig

from our website. Under Device Type, select Network

Peripheral | NL240. Click the

Install the device driver for the

NL240

link and follow the prompts.

•

Ensure the NL240 is powered.

•

Connect the supplied USB cable between a USB port on your computer

and the USB port on the NL240.

•

Open

DevConfig

•

Under

Device Type

, select

Network Peripheral

NL240

•

Click the

Browse

button next to

Communication Port

•

Select the port labeled

NL240

•

Click

•

Click

Connect

•

Configure the NL240 as needed for your application.

•

Click

Apply

to save your changes.

NOTE

Содержание NL240











































































Результаты поиска

Содержание NL240

Отзывы:

Похожие инструкции для NL240

Бренды по названию

Популярные бренды

Campbell NL240, Инструкция по эксплуатации

Результаты поиска

Содержание NL240

Отзывы:

Похожие инструкции для NL240

Бренды по названию

Популярные бренды