Campbell NL240 Скачать руководство пользователя страница 12

Страница: 12 / 74

NL240 Wireless Network Link Interface

3.1 Physical Setup

Attach an antenna to the NL240’s antenna connector. Using the supplied serial

cable, connect the NL240’s CS I/O port to the datalogger’s CS I/O port.

Alternatively, power the NL240 through the barrel-connector jack located on

the edge of the device. Ensure that the device is powered up by inspecting the

Power LED.

FIGURE 3-1. NL240 with CR800 (powered through CS I/O port)

3.2 Configuring the NL240

INSTALL THE DEVICE DRIVER BEFORE plugging the

NL240 into your PC for the first time. You will need the device

driver properly installed before you can connect to the NL240 via

USB. To install the device driver, download the latest version of

DevConfig

from our website. Under Device Type, select Network

Peripheral | NL240. Click the

Install the device driver for the

NL240

link and follow the prompts.

NOTE

Содержание NL240











































































Результаты поиска

Содержание NL240

Отзывы:

Похожие инструкции для NL240

Бренды по названию

Популярные бренды

Campbell NL240, Инструкция по эксплуатации

Результаты поиска

Содержание NL240

Отзывы:

Похожие инструкции для NL240

Бренды по названию

Популярные бренды