Busch-Jaeger Corridor KNX 6131/50 series Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 198

Busch-Jaeger Corridor KNX 6131/50 series Скачать руководство пользователя страница 87

Description of application and parameters

Constant light switch application

KNX Technical Manual 2CKA001473B8667

│

06.02.2017

│

87

11.4.12 Extended parameters — Operating mode

Options:

Automatic mode

Automatic switch-off

Movement-dependent operation

– Automatic = automatic switch-on and switch-off.

In "Automatic" mode, in case it is too dark, the presence detector switches on automatically
when detecting a movement. The switch-off is effected after the set switch-off delay
beginning from the most recent detection.

– Automatic switch-off = manual switch-on and automatic switch-off.

In "Automatic switch-off" mode, the presence detector must be switched on manually using
the “automatic/manual” object. The switch-off is effected automatically under consideration
of the switch-off delay.

– Operation independent of movement = switch-on and switch-off independent of brightness.

In the "Operation independent of movement" mode, the presence detector switches on and
off only on the basis of brightness ± hysteresis. Activation / deactivation via object
“automatic/manual off”.

11.4.13 Extended parameters — Used movement detection

Options:

Internal only

External only

Internal and external

– Only internal: The presence detector responds only to movement measured internally.
– Only external: The presence detector responds only to telegrams that are received via the

“slave” object (input).

– Internal and external: The presence detector responds to movements measured internally

and to external telegrams that are received via the “slave” object (input).

11.4.14 Extended parameters — Slave sent

Options:

Cyclic On telegram

On/off telegram

– Cyclic On telegram: The presence detector, which is connected to the master as slave,

sends only On telegrams cyclically.

– On/Off telegram: The presence detector, which is connected to the master as slave, sends

only On/Off telegrams.

«
...
85
86
87
88
89
...
»

Содержание Corridor KNX 6131/50 series







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды