Busch-Jaeger Corridor KNX 6131/50 series Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 198

Busch-Jaeger Corridor KNX 6131/50 series Скачать руководство пользователя страница 62

Operation

KNX Technical Manual 2CKA001473B8667

│

06.02.2017

│

62

9 Operation

9.1

Operation via IR remote control

The premium version and the Busch-Watchdog Sky KNX have a sensor for receiving infrared
signals. This allows the IR remote control 6010-25 to be used, for example.

Two channels that can be selected on the transmitter are available for operation: the blue and
the white channel.

The following example is to serve as an aid for commissioning. The infrared functions can be
programmed in the device. For button M1 (blue and / or white) the function "Switching, rocker
switch left / right" is selected. The parameter "Reaction to rising edge" is shown within this
function. This parameter is to be set on "ON". The function has the communication object
"Switching". This object must now be connected with the object "Save setpoint" of the constant
light application. This stores the current light value as setpoint as soon as button M1 is pressed.
The light can, for example, be set with the remote control. For this, one or several button pairs
are occupied with the function "Dimming rocker switch total" and connected directly with the
dimming actuator. Now use the button pair selected to set the desired brightness and save the
value with button M1.

9.2 RC-5

Code

Fig. 21: RC-5 code

Note

Please observe also the supplement and the technical reference manual of the
IR remote control. These can be downloaded via the electronic catalogue
(www.busch-jaeger-catalogue.com).

«
...
60
61
62
63
64
...
»

Содержание Corridor KNX 6131/50 series







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды