Busch-Jaeger Corridor KNX 6131/50 series Скачать руководство пользователя страница 108

Страница: 108 / 198

Description of application and parameters

"Constant light controller" application

KNX Technical Manual 2CKA001473B8667

│

06.02.2017

│

108

11.5.46 Enable — At enable, output sends

Options:

Current output value

Start value

– Current output value: During enable it is checked whether a movement has taken place. If

yes, the lighting is switched on. If no, the lighting is switched off.

– Start value: During enable it is checked whether a movement has taken place. If yes, a

switch-on takes place with a start value. If no, 0% is sent and not the parameterised start
value.

11.5.47 Enable — Output sends at blockage

Options:

No telegram

OFF after expiration of the light-on time

Single value for switching off

– No telegram: No telegram is sent during blockage.
– Off after expiry of switch-off delay: During blockage the switch-off delay is started anew and

the detector sends the value that is parameterised under the “value for switch-off” parameter
only after this time has expired.

– Single value for switch-off: During enable the single value which has been parameterised

under the “value for switch-off” parameter is sent.

Содержание Corridor KNX 6131/50 series







































































































































































































Результаты поиска

Содержание Corridor KNX 6131/50 series

Отзывы:

Бренды по названию

Популярные бренды

Busch-Jaeger Corridor KNX 6131/50 series, Техническое руководство

Результаты поиска

Содержание Corridor KNX 6131/50 series

Отзывы:

Бренды по названию

Популярные бренды