manualshive.com logo in svg

Busch-Jaeger Corridor KNX 6131/50 series, Техническое руководство

Поделиться
Скачать
Busch-Jaeger Corridor KNX 6131/50 series Скачать руководство пользователя страница 162

 

Description of application and parameters

Application: "IR functions (white)"

 

 

 

 

KNX Technical Manual  2CKA001473B8667  

│

  06.02.2017 

│

162

 

11.9 

Application: "IR functions (white)" 

11.9.1  Button 1 – 5 (left/right) / memo button M1/M2 

The premium version and the Busch-Watchdog Sky KNX have a sensor for receiving infrared 
signals. This allows the IR remote control 6010-25 to be used, for example.  

Two channels that can be selected on the transmitter are available for operation: the blue and 
the white channel. 

The following example is to serve as an aid for commissioning. The infrared functions can be 
programmed in the device. For button M1 (white) the function "Switching, rocker switch left / 
right" is selected. The parameter "Reaction to rising edge" is shown within this function. This 
parameter is to be set on "ON". The function has the communication object "Switching". This 
object must now be connected with the object "Save setpoint" of the constant light application. 
This stores the current light value as setpoint as soon as button M1 is pressed. The light can, 
for example, be set with the remote control. For this, one or several button pairs are occupied 
with the function "Dimming rocker switch total" and connected directly with the dimming 
actuator. Now use the button pair selected to set the desired brightness and save the value with 
button M1. 

 

11.10 

Application: "IR functions (blue)" 

11.10.1  Button 1 – 5 (left/right) / memo button M1/M2 

The premium version and the Busch-Watchdog Sky KNX have a sensor for receiving infrared 
signals. This allows the IR remote control 6010-25 to be used, for example.  

Two channels that can be selected on the transmitter are available for operation: the blue and 
the white channel. 

The following example is to serve as an aid for commissioning. The infrared functions can be 
programmed in the device. For button M1 (blue) the function "Switching, rocker switch left / 
right" is selected. The parameter "Reaction to rising edge" is shown within this function. This 
parameter is to be set on "ON". The function has the communication object "Switching". This 
object must now be connected with the object "Save setpoint" of the constant light application. 
This stores the current light value as setpoint as soon as button M1 is pressed. The light can, 
for example, be set with the remote control. For this, one or several button pairs are occupied 
with the function "Dimming rocker switch total" and connected directly with the dimming 
actuator. Now use the button pair selected to set the desired brightness and save the value with 
button M1. 

 

 

 

Содержание Corridor KNX 6131/50 series







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды