Busch-Jaeger Corridor KNX 6131/50 series Скачать руководство пользователя страница 107

Страница: 107 / 198

Description of application and parameters

"Constant light controller" application

KNX Technical Manual 2CKA001473B8667

│

06.02.2017

│

107

11.5.42 Sensor selection — Use of sensors 1 - 4

Options:

Yes

– Yes: This sensor is active and detects movement.
– No: This sensor is switched off and movement is no longer detected in this area.

11.5.43 Enable — Presence detector enable object

Options:

Yes

– No: There is no object with which the constant light controller can be blocked or enabled.
– Yes: A 1-bit “enable presence” communication object (input) is being enabled. This object

allows the constant light controller to be enabled or blocked. No telegrams are sent by the
detector during blockage.

11.5.44 Enable — Enable with

Options:

ON telegram

OFF telegram

– On telegram: With the receipt of value 1 on the “enable movement” (input) object, the

detector is enabled and blocked with value 0.

– Off telegram: With the receipt of value 0 on the “enable movement” (input) object, the

detector is enabled and blocked with value 1.

11.5.45 Enable — After bus voltage recovery, presence detector is

Options:

Enabled

Blocked

– Enabled: The device is enabled and functions normally when the bus voltage is interrupted

or the device has been reprogrammed, as well as after a reset.

–

Blocked: The device is blocked and must be enabled for normal function when the bus

voltage is interrupted or the device has been reprogrammed, as well as after a reset.

Содержание Corridor KNX 6131/50 series







































































































































































































Результаты поиска

Содержание Corridor KNX 6131/50 series

Отзывы:

Бренды по названию

Популярные бренды

Busch-Jaeger Corridor KNX 6131/50 series, Техническое руководство

Результаты поиска

Содержание Corridor KNX 6131/50 series

Отзывы:

Бренды по названию

Популярные бренды