Busch-Jaeger Corridor KNX 6131/50 series Скачать руководство пользователя страница 100

Страница: 100 / 198

Description of application and parameters

"Constant light controller" application

KNX Technical Manual 2CKA001473B8667

│

06.02.2017

│

100

11.5.14 Extended parameters — Value for reduced brightness (%)

Options:

0 .. 20 .. 100

Yes

Here the value for the reduced brightness is set. After the switch-off delay has expired the
detector is to dim the light to this value.

Switch-off value

≤

bottom control limit

≤

reduced brightness < upper control or dimming limit.

11.5.15 Extended parameters — Brightness reduced according to switch-off delay (hh:mm:ss)

Options:

00:00:10 .. 00:05:00 .. 18:12:15

– Here the value for the switch-off delay of the reduced brightness is set. The total switch-off

delay then consists of the switch-off delay + brightness reduced according to switch-off
delay.

Used movement detection

Options:

Internal only

External only

Internal and external

– Only internal: The presence detector responds only to movement measured internally.
– Only external: The presence detector responds only to telegrams that are received via the

“slave” object (input).

– Internal and external: The presence detector responds to movements measured internally

and to external telegrams that are received via the “slave” object (input).

11.5.16 Extended parameters — Slave sent

Options:

Cyclic On telegram

On/off telegram

– Cyclic On telegram: The presence detector, which is connected to the master as slave,

sends only On telegrams cyclically.

– On/Off telegram: The presence detector, which is connected to the master as slave, sends

only On/Off telegrams.

Содержание Corridor KNX 6131/50 series







































































































































































































Результаты поиска

Содержание Corridor KNX 6131/50 series

Отзывы:

Бренды по названию

Популярные бренды

Busch-Jaeger Corridor KNX 6131/50 series, Техническое руководство

Результаты поиска

Содержание Corridor KNX 6131/50 series

Отзывы:

Бренды по названию

Популярные бренды