manualshive.com logo in svg

Busch-Jaeger Corridor KNX 6131/50 series, Техническое руководство

Поделиться
Скачать
Busch-Jaeger Corridor KNX 6131/50 series Скачать руководство пользователя страница 156

 

Description of application and parameters

Application "RTC object"

 

 

 

 

KNX Technical Manual  2CKA001473B8667  

│

  06.02.2017 

│

156

 

11.8.113 Fan coil settings — Fan speed levels — Lowest manually adjustable level 

Options: 

Speed level 0 

 

Speed level 1 

 

This parameter is used to preselect the lowest fan speed level that can be set by an operation 
performed at the device. When level 0 is selected, the heating/cooling system will not be in 
operation (fan speed level and valve control 0) as long as the current operating mode and 
operation type are maintained. To avoid damage to the building, level 0 is deactivated after 18 
hours and the device is returned to automatic mode. 

   

 

11.8.114 Fan coil settings — Fan speed levels — Level status evaluation 

Options: 

No 

 

Yes 

 

The controller obtains the current fan speed level for controlling a fan coil actuator either by 
calculating it from the table of level values under "Fan coil settings for heating" or "Fan coil 
settings for cooling," or by receiving feedback from the fan coil actuator. If the "Yes" option is 
selected, the "Fan coil step status" object is activated for receiving the fan speed level from the 
fan coil actuator. 

 

 

 

 

Содержание Corridor KNX 6131/50 series







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды