Burster 9181, Инструкция по эксплуатации

Страница: 39 / 55

The figure 19.1 shows the indication (SCAL) corresponding to the scal menu . Press
ENTER
key to access this menu.
ENTER
Access to scale configuration
Go to next programming step.
ESC
Cancel programming and returns to run mode.
The previously programmed INP1 value appears on the display, LED INP1 activated,
with the digit (sign) in flash. There are two methods to program input values:
Key-in method: Use
to switch between "0" (positive) and "-" (negative).
Press to advance to the next digit to the right which goes in flash. Press
repeatedly to increment the active digit until it takes desired value. Proceed in
the same manner with all the digits until desired value is completed on the display
with sign. Press
ENTER
to accept this value as INP1 and go next step.
Teach method: Apply signal to the meter input. Press
TEACH
to view the actual
signal value present at the input connector (LED INP1 flashes). Press
ENTER
to accept
this value as INP1 and go next step.
ESC
To exit from the programming mode without saving changes.
The previously programmed DSP1 value appears on the display, LED DSP1 activated,
with the digit (sign) in flash. By means of the
and procedure, program
desired DSP1 value and press
ENTER
. The limits of the span are -9999 and 9999
points.
ENTER
Validate data and access to next programming step.
ESC
Cancel programming and returns to run mode.
B
A
TARE
HOLD LIMIT MAX MIN DATA
DSP2 INP2 FLT STORE DSP1 INP1
2
1
4
3
TARE
RESET LIMIT MAX/MIN ENTER
ESC DATA
PROG
TEACH
PRG
RUN
[19.1] Scale configuration
In this menu will be intoduced the necessary parametres that configs the scal (INP1-DSP1 – decimal point – INP2-DSP2 and if
needed up to 29 aditional points). By default, the instrument waits the introduction of this values by keyboard. The input values
can be programmed by keyboard or measuring directly the input signal by method Teack, push in this case the key
TEACH
.
MENU 2A - SCALE
[19.2] Input 1 value
B
A
TARE
HOLD LIMIT MAX MIN DATA
DSP2 INP2 FLT STORE DSP1 INP1
2
1
4
3 TARE
RESET LIMIT MAX/MIN ENTER
ESC DATA
PROG
TEACH
PRG
RUN
19
[19.3] Display 1 value
B
A
TARE
HOLD LIMIT MAX MIN DATA
DSP2 INP2 FLT STORE DSP1 INP1
2
1
4
3
TARE
RESET LIMIT MAX/MIN ENTER
ESC DATA
PROG
TEACH
PRG
RUN
39
The figure page 39 shows the different locations of
the plug-in output cards. Each location corresponds to
a specific function: setpoints, analogue and serial
outputs.
The options 2RE, 4RE, 4OP and 4OPP are installed in
the M5 connector.
The ANA option is installed in the M4 connector.
The options RS2 and RS4 are installed in the M1
connector.
Up to three output options can be present at a time
and operate simultaneously, but only one from each
category:
- ANALOGUE
- RS232C or RS485
- 2 RELAYS, 4 RELAYS, 4 PNP or 4 NPN
ANALOG
OUTPUT
OPTION
CONNECTOR
RELAYS
OUTPUT
OPTION
CONNECTOR
SERIAL
OUTPUT
OPTION
CONNECTOR
A/D
CONVERTER
CONNECTOR
ANALOG
OUTPUT
OPTION
SERIAL
OUTPUT
OPTION
RELAYS
OUTPUT
OPTION