The previously programmed INP4 value appears on the display, LED INP2 activated.
There are two methods to program input values :
Key-in method: Use
to switch between "0" (positive) and "-" (negative).
Press
to advance to the next digit to the right which goes in flash. Press
repeatedly
to increment the active digit until it takes desired value. Proceed in
the same manner with all the digits until desired value is completed on the display
with sign. Press
ENTER
to accept this value as INP4 and go next step.
Teach method: Apply signal to the meter input. Press
TEACH
to view the actual
signal value present at the input connector, LED INP2 flashes. Press
ENTER
to accept
this value as INP4 and go next step.
ESC
To exit from the programming mode without saving changes.
Display value programming in point 4, led DSP2 turned on
.
By means of the
and
procedure, program desired DSP3 value and press
ENTER
. The limits of the span are -9999 and 9999 points.
a.
To validate data and advance to the next point ; press
ENTER
; or
b.
To save the programmed data in the memory and return to the run mode (the
meter is scaled by three segments), press and hold down
ENTER
for 3 seconds.
ESC
To exit from the programming mode without saving changes.
1 second flag indication for scaling point 4.
NOTE: The instructions given for programming point 4 are applicable to the
programming of points up to 30
22
[22.2] Input 4 value
B
A
TARE
HOLD
LIMIT
MAX
MIN
DATA
DSP2
INP2
FLT
STORE
DSP1
INP1
2
1
4
3
TARE
RESET
LIMIT
MAX/MIN
ENTER
ESC
DATA
PROG
TEACH
PRG
RUN
[22.3] Display 4 value
B
A
TARE
HOLD
LIMIT
MAX
MIN
DATA
DSP2
INP2
FLT
STORE
DSP1
INP1
2
1
4
3
TARE
RESET
LIMIT
MAX/MIN
ENTER
ESC
DATA
PROG
TEACH
PRG
RUN
[22.2] Point 4
B
A
TARE
HOLD
LIMIT
MAX
MIN
DATA
DSP2
INP2
FLT
STORE
DSP1
INP1
2
1
4
3
TARE
RESET
LIMIT
MAX/MIN
ENTER
ESC
DATA
PROG
TEACH
PRG
RUN
2
INTRODUCTION TO THE DIGIMASTER
This manual does not constitute a formal agreement.
All information given in this manual is subject to
change without notice.
The DIGIMASTER brings a new phylosophy in digital panel
instrumentation which is expressed by multipurpose,
modular-concept devices providing a rich array of basic
functions and advanced capabilities.
With a fully MODULAR DESIGN, it is possible to implement a
wide variety of applications by only adding the adequate
options.
Intelligence within allows the meter to recognize the options
installed and ask for the necessary parameters to properly
function within desired margins. The paramenters related to
non-installed options are removed from the program routines.
The instruments CALIBRATION is made at the factory
eliminating the need for adjustment potentiometers.
Any circuit or option liable to be adjusted incorporates a
memory where calibration parameters are stored, making it
possible the optional cards be totally interchangeable without
need of any subsequent adjust.
Custom CONFIGURATION for specific applications can be made
quickly and easily through five front panel keys, following
structured choice menus aided by display prompts at each
programming step.
Other features of the DIGIMASTER family include :
•
CONNECTIONS via plug-in terminal blocks without
screws and CLEMP-WAGO clips cable retention system.
•
DIMENSIONS
Models Typ 9180 & Typ 9181 96x48x120 mm DIN 43700
Model Typ 9186 96x48x60 mm DIN 43700
•
CASE MATERIAL UL-94 V0-rated polycarbonate.
•
PANEL INSTALLATION without screws by means of single
part fastening clips.
To guarantee the meter's technical specifications, it is
recommended to recalibrate the meter at periodical intervals
according to the ISO9001 standards for the particular
application operating criteria. Calibration should be perfomed
at the factory or in a qualified laboratory.